[ Upstream commit 3128b0a2e0 ]
In multi-cluster MIPS I6500 systems there is a GIC in each cluster,
each with its own counter. When a cluster powers up the counter will
be stopped, with the COUNTSTOP bit set in the GIC_CONFIG register.
In single cluster systems, it has been fine to clear COUNTSTOP once
in gic_clocksource_of_init() to start the counter. In multi-cluster
systems, this will only have started the counter in the boot cluster,
and any CPUs in other clusters will find their counter stopped which
will break the GIC clock_event_device.
Resolve this by having CPUs clear the COUNTSTOP bit when they come
online, using the existing gic_starting_cpu() CPU hotplug callback. This
will allow CPUs in secondary clusters to ensure that the cluster's GIC
counter is running as expected.
Signed-off-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: Chao-ying Fu <cfu@wavecomp.com>
Signed-off-by: Dragan Mladjenovic <dragan.mladjenovic@syrmia.com>
Signed-off-by: Aleksandar Rikalo <arikalo@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 94cff94634 upstream.
On x86 during boot, clockevent_i8253_disable() can be invoked via
x86_late_time_init -> hpet_time_init() -> pit_timer_init() which happens
with enabled interrupts.
If some of the old i8253 hardware is actually used then lockdep will notice
that i8253_lock is used in hard interrupt context. This causes lockdep to
complain because it observed the lock being acquired with interrupts
enabled and in hard interrupt context.
Make clockevent_i8253_disable() acquire the lock with
raw_spinlock_irqsave() to cure this.
[ tglx: Massage change log and use guard() ]
Fixes: c8c4076723 ("x86/timer: Skip PIT initialization on modern chipsets")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250404133116.p-XRWJXf@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 531b2ca0a9 upstream.
According to the data sheet, writing the MODE register should stop the
counter (and thus the interrupts). This appears to work on real hardware,
at least modern Intel and AMD systems. It should also work on Hyper-V.
However, on some buggy virtual machines the mode change doesn't have any
effect until the counter is subsequently loaded (or perhaps when the IRQ
next fires).
So, set MODE 0 and then load the counter, to ensure that those buggy VMs
do the right thing and the interrupts stop. And then write MODE 0 *again*
to stop the counter on compliant implementations too.
Apparently, Hyper-V keeps firing the IRQ *repeatedly* even in mode zero
when it should only happen once, but the second MODE write stops that too.
Userspace test program (mostly written by tglx):
=====
#include <stdio.h>
#include <unistd.h>
#include <stdlib.h>
#include <stdint.h>
#include <sys/io.h>
static __always_inline void __out##bwl(type value, uint16_t port) \
{ \
asm volatile("out" #bwl " %" #bw "0, %w1" \
: : "a"(value), "Nd"(port)); \
} \
\
static __always_inline type __in##bwl(uint16_t port) \
{ \
type value; \
asm volatile("in" #bwl " %w1, %" #bw "0" \
: "=a"(value) : "Nd"(port)); \
return value; \
}
BUILDIO(b, b, uint8_t)
#define inb __inb
#define outb __outb
#define PIT_MODE 0x43
#define PIT_CH0 0x40
#define PIT_CH2 0x42
static int is8254;
static void dump_pit(void)
{
if (is8254) {
// Latch and output counter and status
outb(0xC2, PIT_MODE);
printf("%02x %02x %02x\n", inb(PIT_CH0), inb(PIT_CH0), inb(PIT_CH0));
} else {
// Latch and output counter
outb(0x0, PIT_MODE);
printf("%02x %02x\n", inb(PIT_CH0), inb(PIT_CH0));
}
}
int main(int argc, char* argv[])
{
int nr_counts = 2;
if (argc > 1)
nr_counts = atoi(argv[1]);
if (argc > 2)
is8254 = 1;
if (ioperm(0x40, 4, 1) != 0)
return 1;
dump_pit();
printf("Set oneshot\n");
outb(0x38, PIT_MODE);
outb(0x00, PIT_CH0);
outb(0x0F, PIT_CH0);
dump_pit();
usleep(1000);
dump_pit();
printf("Set periodic\n");
outb(0x34, PIT_MODE);
outb(0x00, PIT_CH0);
outb(0x0F, PIT_CH0);
dump_pit();
usleep(1000);
dump_pit();
dump_pit();
usleep(100000);
dump_pit();
usleep(100000);
dump_pit();
printf("Set stop (%d counter writes)\n", nr_counts);
outb(0x30, PIT_MODE);
while (nr_counts--)
outb(0xFF, PIT_CH0);
dump_pit();
usleep(100000);
dump_pit();
usleep(100000);
dump_pit();
printf("Set MODE 0\n");
outb(0x30, PIT_MODE);
dump_pit();
usleep(100000);
dump_pit();
usleep(100000);
dump_pit();
return 0;
}
=====
Suggested-by: Sean Christopherson <seanjc@google.com>
Co-developed-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhkelley@outlook.com>
Link: https://lore.kernel.org/all/20240802135555.564941-2-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70e6b7d9ae upstream.
Leaving the PIT interrupt running can cause noticeable steal time for
virtual guests. The VMM generally has a timer which toggles the IRQ input
to the PIC and I/O APIC, which takes CPU time away from the guest. Even
on real hardware, running the counter may use power needlessly (albeit
not much).
Make sure it's turned off if it isn't going to be used.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhkelley@outlook.com>
Link: https://lore.kernel.org/all/20240802135555.564941-1-dwmw2@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcc80dec91 upstream.
read_hv_sched_clock_tsc() assumes that the Hyper-V clock counter is
bigger than the variable hv_sched_clock_offset, which is cached during
early boot, but depending on the timing this assumption may be false
when a hibernated VM starts again (the clock counter starts from 0
again) and is resuming back (Note: hv_init_tsc_clocksource() is not
called during hibernation/resume); consequently,
read_hv_sched_clock_tsc() may return a negative integer (which is
interpreted as a huge positive integer since the return type is u64)
and new kernel messages are prefixed with huge timestamps before
read_hv_sched_clock_tsc() grows big enough (which typically takes
several seconds).
Fix the issue by saving the Hyper-V clock counter just before the
suspend, and using it to correct the hv_sched_clock_offset in
resume. This makes hv tsc page based sched_clock continuous and ensures
that post resume, it starts from where it left off during suspend.
Override x86_platform.save_sched_clock_state and
x86_platform.restore_sched_clock_state routines to correct this as soon
as possible.
Note: if Invariant TSC is available, the issue doesn't happen because
1) we don't register read_hv_sched_clock_tsc() for sched clock:
See commit e5313f1c54 ("clocksource/drivers/hyper-v: Rework
clocksource and sched clock setup");
2) the common x86 code adjusts TSC similarly: see
__restore_processor_state() -> tsc_verify_tsc_adjust(true) and
x86_platform.restore_sched_clock_state().
Cc: stable@vger.kernel.org
Fixes: 1349401ff1 ("clocksource/drivers/hyper-v: Suspend/resume Hyper-V clocksource for hibernation")
Co-developed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240917053917.76787-1-namjain@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240917053917.76787-1-namjain@linux.microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0309f714a0 ]
The sp804 is currently only user selectable if COMPILE_TEST, this was
done by commit dfc82faad7 ("clocksource/drivers/sp804: Add
COMPILE_TEST to CONFIG_ARM_TIMER_SP804") in order to avoid it being
spuriously offered on platforms that won't have the hardware since it's
generally only seen on Arm based platforms. This config is overly
restrictive, while platforms that rely on the SP804 do select it in
their Kconfig there are others such as the Arm fast models which have a
SP804 available but currently unused by Linux. Relax the dependency to
allow it to be user selectable on arm and arm64 to avoid surprises and
in case someone comes up with a use for extra timer hardware.
Fixes: dfc82faad7 ("clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804")
Reported-by: Ross Burton <ross.burton@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241001-arm64-vexpress-sp804-v3-1-0a2d3f7883e4@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 471ef0b5a8 upstream.
GCC's named address space checks errors out with:
drivers/clocksource/timer-of.c: In function ‘timer_of_irq_exit’:
drivers/clocksource/timer-of.c:29:46: error: passing argument 2 of
‘free_percpu_irq’ from pointer to non-enclosed address space
29 | free_percpu_irq(of_irq->irq, clkevt);
| ^~~~~~
In file included from drivers/clocksource/timer-of.c:8:
./include/linux/interrupt.h:201:43: note: expected ‘__seg_gs void *’
but argument is of type ‘struct clock_event_device *’
201 | extern void free_percpu_irq(unsigned int, void __percpu *);
| ^~~~~~~~~~~~~~~
drivers/clocksource/timer-of.c: In function ‘timer_of_irq_init’:
drivers/clocksource/timer-of.c:74:51: error: passing argument 4 of
‘request_percpu_irq’ from pointer to non-enclosed address space
74 | np->full_name, clkevt) :
| ^~~~~~
./include/linux/interrupt.h:190:56: note: expected ‘__seg_gs void *’
but argument is of type ‘struct clock_event_device *’
190 | const char *devname, void __percpu *percpu_dev_id)
Sparse warns about:
timer-of.c:29:46: warning: incorrect type in argument 2 (different address spaces)
timer-of.c:29:46: expected void [noderef] __percpu *
timer-of.c:29:46: got struct clock_event_device *clkevt
timer-of.c:74:51: warning: incorrect type in argument 4 (different address spaces)
timer-of.c:74:51: expected void [noderef] __percpu *percpu_dev_id
timer-of.c:74:51: got struct clock_event_device *clkevt
It appears the code is incorrect as reported by Uros Bizjak:
"The referred code is questionable as it tries to reuse
the clkevent pointer once as percpu pointer and once as generic
pointer, which should be avoided."
This change removes the percpu related code as no drivers is using it.
[Daniel: Fixed the description]
Fixes: dc11bae785 ("clocksource/drivers: Add timer-of common init routine")
Reported-by: Uros Bizjak <ubizjak@gmail.com>
Tested-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20240819100335.2394751-1-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b8843fcd4 upstream.
In tpm_set_next_event(delta), return -ETIME by wrong cast to int when delta
is larger than INT_MAX.
For example:
tpm_set_next_event(delta = 0xffff_fffe)
{
...
next = tpm_read_counter(); // assume next is 0x10
next += delta; // next will 0xffff_fffe + 0x10 = 0x1_0000_000e
now = tpm_read_counter(); // now is 0x10
...
return (int)(next - now) <= 0 ? -ETIME : 0;
^^^^^^^^^^
0x1_0000_000e - 0x10 = 0xffff_fffe, which is -2 when
cast to int. So return -ETIME.
}
To fix this, introduce a 'prev' variable and check if 'now - prev' is
larger than delta.
Cc: stable@vger.kernel.org
Fixes: 059ab7b82e ("clocksource/drivers/imx-tpm: Add imx tpm timer support")
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240725193355.1436005-1-Frank.Li@nxp.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e651f2fae3 ]
The result of the division of new_rate by gt_target_rate can be zero (if
new_rate is smaller than gt_target_rate). Using that result as divisor
without checking can result in a division by zero error. Guard against
this by checking for a zero value earlier.
While here, also change the psv variable to an unsigned long to make
sure we don't overflow the datatype as all other types involved are also
unsiged long.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240225151336.2728533-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db19d3aa77 ]
There is a race condition in the CMT interrupt handler. In the interrupt
handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This
flag is used to indicate any call to set_next_event() should not be
directly propagated to the device, but instead cached. This is done as
the interrupt handler itself reprograms the device when needed before it
completes and this avoids this operation to take place twice.
It is unclear why this design was chosen, my suspicion is to allow the
struct clock_event_device.event_handler callback, which is called while
the FLAG_IRQCONTEXT is set, can update the next event without having to
write to the device twice.
Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is
set and later cleared where the interrupt handler have already started to
write the next event to the device. If set_next_event() is called in
this window the value is only cached in the driver but not written. This
leads to the board to misbehave, or worse lockup and produce a splat.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?)
rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2)
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty #20
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : tick_check_broadcast_expired+0xc/0x40
lr : cpu_idle_poll.isra.0+0x8c/0x168
sp : ffff800081c63d70
x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610
x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c
x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8
x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0
x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028
x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000
x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008
Call trace:
tick_check_broadcast_expired+0xc/0x40
do_idle+0x9c/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x11c
do_one_initcall+0x0/0x260
__primary_switched+0x80/0x88
rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
rcu: Possible timer handling issue on cpu=0 timer-softirq=262
rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008
Call trace:
__switch_to+0xbc/0x100
__schedule+0x358/0xbe0
schedule+0x48/0x148
schedule_timeout+0xc4/0x138
rcu_gp_fqs_loop+0x12c/0x764
rcu_gp_kthread+0x208/0x298
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
The design have been part of the driver since it was first merged in
early 2009. It becomes increasingly harder to trigger the issue the
older kernel version one tries. It only takes a few boots on v6.10-rc5,
while hundreds of boots are needed to trigger it on v5.10.
Close the race condition by using the CMT channel lock for the two
competing sections. The channel lock was added to the driver after its
initial design.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20240702190230.3825292-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d3bc4c02d ]
On SAM9 hardware two cascaded 16 bit timers are used to form a 32 bit
high resolution timer that is used as scheduler clock when the kernel
has been configured that way (CONFIG_ATMEL_CLOCKSOURCE_TCB).
The driver initially triggers a reset-to-zero of the two timers but this
reset is only performed on the next rising clock. For the first timer
this is ok - it will be in the next 60ns (16MHz clock). For the chained
second timer this will only happen after the first timer overflows, i.e.
after 2^16 clocks (~4ms with a 16MHz clock). So with other words the
scheduler clock resets to 0 after the first 2^16 clock cycles.
It looks like that the scheduler does not like this and behaves wrongly
over its lifetime, e.g. some tasks are scheduled with a long delay. Why
that is and if there are additional requirements for this behaviour has
not been further analysed.
There is a simple fix for resetting the second timer as well when the
first timer is reset and this is to set the ATMEL_TC_ASWTRG_SET bit in
the Channel Mode register (CMR) of the first timer. This will also rise
the TIOA line (clock input of the second timer) when a software trigger
respective SYNC is issued.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231007161803.31342-1-rwahl@gmx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b5bf64c89 ]
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Fixes: e932900a32 ("arm: zynq: Use standard timer binding")
Fixes: 70504f311d ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Signed-off-by: Feng Mingxi <m202271825@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230425065611.702917-1-m202271825@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f44f7156f ]
Documentation for most CMTs say that it takes two input clocks before
changes propagate to the timer. This is especially relevant when the timer
is stopped to change further settings.
Implement the delays according to the spec. To avoid unnecessary delays in
atomic mode, also check if the to-be-written value actually differs.
CMCNT is a bit special because testing showed that it requires 3 cycles to
propagate, which affects all CMTs. Also, the WRFLAG needs to be checked
before writing. This fixes "cannot clear CMCNT" messages which occur often
on R-Car Gen4 SoCs, but only very rarely on older SoCs for some reason.
Fixes: 81b3b27110 ("clocksource: sh_cmt: Add support for multiple channels per device")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20221130210609.7718-1-wsa+renesas@sang-engineering.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9f15a9de4 ]
This reverts commit 232ccac1bd.
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
io scheduler mq-deadline registered
io scheduler kyber registered
microchip-pcie 2000000000.pcie: host bridge /soc/pcie@2000000000 ranges:
microchip-pcie 2000000000.pcie: MEM 0x2008000000..0x2087ffffff -> 0x0008000000
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: axi read request error
microchip-pcie 2000000000.pcie: axi read timeout
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
Freeing initrd memory: 7332K
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
Fixes: 232ccac1bd ("clocksource/drivers/riscv: Events are stopped during CPU suspend")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/
Link: https://github.com/riscv-non-isa/riscv-sbi-doc/issues/98/
Link: https://lore.kernel.org/linux-riscv/bf6d3b1f-f703-4a25-833e-972a44a04114@sholland.org/
Link: https://lore.kernel.org/r/20221122121620.3522431-1-conor.dooley@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
ixp4xx_timer_setup is exported, and so can not be an __init function.
But it does not need to be exported as it is only called from one
in-kernel function, so just remove the EXPORT_SYMBOL_GPL() marking to
resolve the build warning.
This is fixed "properly" in commit 41929c9f62
("clocksource/drivers/ixp4xx: Drop boardfile probe path") but that can
not be backported to older kernels as the reworking of the IXP4xx
codebase is not suitable for stable releases.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 245b993d8f ]
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
arch/x86/kernel/cpu/mshyperv.c is never compiled as modular.
(CONFIG_HYPERVISOR_GUEST is boolean)
Fixes: dd2cb34861 ("clocksource/drivers: Continue making Hyper-V clocksource ISA agnostic")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220606050238.4162200-1-masahiroy@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a98399cbc1 ]
When a machine sports more than one SP804 timer instance, we only bring
up the first one, since multiple timers of the same kind are not useful
to Linux. As this is intentional behaviour, we should not return an
error message, as we do today:
===============
[ 0.000800] Failed to initialize '/bus@8000000/motherboard-bus@8000000/iofpga-bus@300000000/timer@120000': -22
===============
Replace the -EINVAL return with a debug message and return 0 instead.
Also we do not reach the init function anymore if the DT node is
disabled (as this is now handled by OF_DECLARE), so remove the explicit
check for that case.
This fixes a long standing bogus error when booting ARM's fastmodels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220506162522.3675399-1-andre.przywara@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a861abcee ]
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
The __setup() handler interface isn't meant to handle negative return
values -- they are non-zero, so they mean "handled" (like a return
value of 1 does), but that's just a quirk. So return 1 from
parse_pmtmr(). Also print a warning message if kstrtouint() returns
an error.
Fixes: 6b148507d3 ("pmtmr: allow command line override of ioport")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab8da93dc0 ]
The driver statically defines maximum number of interrupts it can
handle, however it does not respect that limit when configuring them.
When provided with a DTS with more interrupts than assumed, the driver
will overwrite static array mct_irqs leading to silent memory
corruption.
Validate the interrupts coming from DTS to avoid this. This does not
change the fact that such DTS might not boot at all, because it is
simply incompatible, however at least some warning will be printed.
Fixes: 36ba5d527e ("ARM: EXYNOS: add device tree support for MCT controller driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220220103815.135380-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8840f5460a ]
Devkit8000 board seems to always used 32k_counter as clocksource.
Restore this behavior.
If clocksource is back to 32k_counter, timer12 is now the clockevent
source (as before) and timer2 is not longer needed here.
This commit fixes the same issue observed with commit 23885389db
("ARM: dts: Fix timer regression for beagleboard revision c") when sleep
is blocked until hitting keys over serial console.
Fixes: aba1ad05da ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23885389db ]
Commit e428e250fd ("ARM: dts: Configure system timers for omap3")
caused a timer regression for beagleboard revision c where the system
clockevent stops working if omap3isp module is unloaded.
Turns out we still have beagleboard revisions a-b4 capacitor c70 quirks
applied that limit the usable timers for no good reason. This also affects
the power management as we use the system clock instead of the 32k clock
source.
Let's fix the issue by adding a new omap3-beagle-ab4.dts for the old timer
quirks. This allows us to remove the timer quirks for later beagleboard
revisions. We also need to update the related timer quirk check for the
correct compatible property.
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Cc: linux-kernel@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull MIPS updates from Thomas Bogendoerfer:
- converted Pistachio platform to use MIPS generic kernel
- fixes and cleanups
* tag 'mips_5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (29 commits)
MIPS: Malta: fix alignment of the devicetree buffer
MIPS: ingenic: Unconditionally enable clock of CPU #0
MIPS: mscc: ocelot: mark the phy-mode for internal PHY ports
MIPS: mscc: ocelot: disable all switch ports by default
MAINTAINERS: adjust PISTACHIO SOC SUPPORT after its retirement
MIPS: Return true/false (not 1/0) from bool functions
MIPS: generic: Return true/false (not 1/0) from bool functions
MIPS: Make a alias for pistachio_defconfig
MIPS: Retire MACH_PISTACHIO
MIPS: config: generic: Add config for Marduk board
pinctrl: pistachio: Make it as an option
phy: pistachio-usb: Depend on MIPS || COMPILE_TEST
clocksource/drivers/pistachio: Make it selectable for MIPS
clk: pistachio: Make it selectable for generic MIPS kernel
MIPS: DTS: Pistachio add missing cpc and cdmm
MIPS: generic: Allow generating FIT image for Marduk board
MIPS: locking/atomic: Fix atomic{_64,}_sub_if_positive
MIPS: loongson2ef: don't build serial.o unconditionally
MIPS: Replace deprecated CPU-hotplug functions.
MIPS: Alchemy: Fix spelling contraction "cant" -> "can't"
...
Pull hyperv updates from Wei Liu:
- make Hyper-V code arch-agnostic (Michael Kelley)
- fix sched_clock behaviour on Hyper-V (Ani Sinha)
- fix a fault when Linux runs as the root partition on MSHV (Praveen
Kumar)
- fix VSS driver (Vitaly Kuznetsov)
- cleanup (Sonia Sharma)
* tag 'hyperv-next-signed-20210831' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv_utils: Set the maximum packet size for VSS driver to the length of the receive buffer
Drivers: hv: Enable Hyper-V code to be built on ARM64
arm64: efi: Export screen_info
arm64: hyperv: Initialize hypervisor on boot
arm64: hyperv: Add panic handler
arm64: hyperv: Add Hyper-V hypercall and register access utilities
x86/hyperv: fix root partition faults when writing to VP assist page MSR
hv: hyperv.h: Remove unused inline functions
drivers: hv: Decouple Hyper-V clock/timer code from VMbus drivers
x86/hyperv: add comment describing TSC_INVARIANT_CONTROL MSR setting bit 0
Drivers: hv: Move Hyper-V misc functionality to arch-neutral code
Drivers: hv: Add arch independent default functions for some Hyper-V handlers
Drivers: hv: Make portions of Hyper-V init code be arch neutral
x86/hyperv: fix for unwanted manipulation of sched_clock when TSC marked unstable
asm-generic/hyperv: Add missing #include of nmi.h
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55 ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
All arm64 CPUs feature an architected timer, which offers a relatively
low-latency interface to a per-cpu clocksource and timer. For the most
part, using this interface is a no-brainer, with the exception of SoCs
where it cannot be used to wake up from deep idle state (i.e.
CLOCK_EVT_FEAT_C3STOP is set).
On the contrary, the Exynos MCT is extremely slow to access yet can be
used as a wakeup source. In preparation for using the Exynos MCT as a
potential wakeup timer for the Arm architected timer, reduce its ratings
so that the architected timer is preferred.
This effectively reverts the decision made in 6282edb72b
("clocksource/drivers/exynos_mct: Increase priority over ARM arch timer")
for arm64, as the reasoning for the original change was to work around
a 32-bit SoC design.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> # exynos-5422
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210608154341.10794-2-will@kernel.org
This rewrites the IXP4xx watchdog driver as follows:
- Spawn the watchdog driver as a platform device from the timer
driver. It's one device in the hardware, and the fact that
Linux splits the handling into two different devices is
a Linux pecularity, and thus it becomes a Linux pecularity
to spawn a separate watchdog driver.
- Spawn the watchdog driver from the timer driver at probe().
This is well after the timer driver as actually registered and
started and we know the register base is available.
- Instead of looping back callbacks to the timer drivers for all
watchdog calls, pass the register base to the watchdog driver
and manage the registers there. The two drivers aren't even
interested in the same register so the spinlock is totally
surplus, delete it.
- Replace pretty much all of the content in the watchdog driver
with a simple, modern watchdog driver utilizing the watchdog
core instead of registering its own misc device and ioctl()
handling.
- Drop module parameters as the same already exist in the
watchdog core.
What remains is a slim elegant (IMO) watchdog driver using the
watchdog core, spawning from device tree or boardfile alike.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hyper-V clock/timer code in hyperv_timer.c is mostly independent from
other VMbus drivers, but building for ARM64 without hyperv_timer.c
shows some remaining entanglements. A default implementation of
hv_read_reference_counter can just read a Hyper-V synthetic register
and be independent of hyperv_timer.c, so move this code out and into
hv_common.c. Then it can be used by the timesync driver even if
hyperv_timer.c isn't built on a particular architecture. If
hyperv_timer.c *is* built, it can override with a faster implementation.
Also provide stubs for stimer functions called by the VMbus driver when
hyperv_timer.c isn't built.
No functional changes.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1626220906-22629-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
