[ Upstream commit aff12700b8 ]
idt_scan_mws() puts a large fixed-size array on the stack and copies
it into a smaller dynamically allocated array at the end. On 32-bit
targets, the fixed size can easily exceed the warning limit for
possible stack overflow:
drivers/ntb/hw/idt/ntb_hw_idt.c:1041:27: error: stack frame size (1032) exceeds limit (1024) in 'idt_scan_mws' [-Werror,-Wframe-larger-than]
Change it to instead just always use dynamic allocation for the
array from the start. It's too big for the stack, but not actually
all that much for a permanent allocation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/all/202205111109.PiKTruEj-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fd5625fc86 upstream.
msi_db_mask is of type 'u64', still the standard 'int' arithmetic is
performed to compute its value.
While most of the ntb_hw drivers actually don't utilize the higher 32
bits of the doorbell mask now, this may be the case for Switchtec - see
switchtec_ntb_init_db().
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2b0569b3b7 ("NTB: Add MSI interrupt support to ntb_transport")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4279e72cab upstream.
The function call “dmaengine_unmap_put(unmap)” was used in an if branch.
The same call was immediately triggered by a subsequent goto statement.
Thus avoid such a call repetition.
This issue was detected by using the Coccinelle software.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Cc: stable@vger.kernel.org
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de203da734 ]
There is a kernel API ntb_mw_clear_trans() would pass 0 to both addr and
size. This would make xlate_pos negative.
[ 23.734156] switchtec switchtec0: MW 0: part 0 addr 0x0000000000000000 size 0x0000000000000000
[ 23.734158] ================================================================================
[ 23.734172] UBSAN: shift-out-of-bounds in drivers/ntb/hw/mscc/ntb_hw_switchtec.c:293:7
[ 23.734418] shift exponent -1 is negative
Ensuring xlate_pos is a positive or zero before BIT.
Fixes: 1e2fd202f8 ("ntb_hw_switchtec: Check for alignment of the buffer in mw_set_trans()")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e51aded92d ]
In the switchtec_ntb_add function, it can call switchtec_ntb_init_sndev
function, then &sndev->check_link_status_work is bound with
check_link_status_work. switchtec_ntb_link_notification may be called
to start the work.
If we remove the module which will call switchtec_ntb_remove to make
cleanup, it will free sndev through kfree(sndev), while the work
mentioned above will be used. The sequence of operations that may lead
to a UAF bug is as follows:
CPU0 CPU1
| check_link_status_work
switchtec_ntb_remove |
kfree(sndev); |
| if (sndev->link_force_down)
| // use sndev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in switchtec_ntb_remove.
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e229897d37 ]
The debugfs_create_dir() function returns error pointers.
It never returns NULL. So use IS_ERR() to check it.
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5a7693e6bb upstream.
ntb_transport_tx_free_entry() never returns 0 with the current
calculation. If head == tail, then it would return qp->tx_max_entry.
Change compare to tail >= head and when they are equal, a 0 would be
returned.
Fixes: e74bfeedad ("NTB: Add flow control to the ntb_netdev")
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: renlonglong <ren.longlong@h3c.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc79bd2738 upstream.
The tx tail index is not reset when the link goes down. This causes the
tail index to go out of sync when the link goes down and comes back up.
Refactor the ntb_qp_link_down_reset() and reset the tail index as well.
Fixes: 2849b5d706 ("NTB: Reset transport QP link stats on down")
Reported-by: Yuan Y Lu <yuan.y.lu@intel.com>
Tested-by: Yuan Y Lu <yuan.y.lu@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f195a1a6fe upstream.
Currently when the transport receive packets after netdev has closed the
transport returns error and triggers tx errors to be incremented and
carrier to be stopped. There is no reason to return error if the device is
already closed. Drop the packet and return 0.
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Reported-by: Yuan Y Lu <yuan.y.lu@intel.com>
Tested-by: Yuan Y Lu <yuan.y.lu@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2790143f09 ]
As the devm_kcalloc may return NULL pointer,
it should be better to add check for the return
value, as same as the others.
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8623ccbfc5 ]
If device_register() returns error, the name allocated by
dev_set_name() need be freed. As comment of device_register()
says, it should use put_device() to give up the reference in
the error path. So fix this by calling put_device(), then the
name can be freed in kobject_cleanup(), and client_dev is freed
in ntb_transport_client_release().
Fixes: fce8a7bb5b ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c3c796aca ]
A problem about ntb_hw_intel create debugfs failed is triggered with the
following log given:
[ 273.112733] Intel(R) PCI-E Non-Transparent Bridge Driver 2.0
[ 273.115342] debugfs: Directory 'ntb_hw_intel' with parent '/' already present!
The reason is that intel_ntb_pci_driver_init() returns
pci_register_driver() directly without checking its return value, if
pci_register_driver() failed, it returns without destroy the newly created
debugfs, resulting the debugfs of ntb_hw_intel can never be created later.
intel_ntb_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98af0a33c1 ]
A problem about ntb_hw_amd create debugfs failed is triggered with the
following log given:
[ 618.431232] AMD(R) PCI-E Non-Transparent Bridge Driver 1.0
[ 618.433284] debugfs: Directory 'ntb_hw_amd' with parent '/' already present!
The reason is that amd_ntb_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_amd can never be created later.
amd_ntb_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: a1b3695820 ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c012968259 ]
A problem about ntb_hw_idt create debugfs failed is triggered with the
following log given:
[ 1236.637636] IDT PCI-E Non-Transparent Bridge Driver 2.0
[ 1236.639292] debugfs: Directory 'ntb_hw_idt' with parent '/' already present!
The reason is that idt_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_idt can never be created later.
idt_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: bf2a952d31 ("NTB: Add IDT 89HPESxNTx PCIe-switches support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 45e1058b77 upstream.
The call to:
ret = simple_write_to_buffer(buf, size, offp, ubuf, size);
will return success if it is able to write even one byte to "buf".
The value of "*offp" controls which byte. This could result in
reading uninitialized data when we do the sscanf() on the next line.
This code is not really desigined to handle partial writes where
*offp is non-zero and the "buf" is preserved and re-used between writes.
Just ban partial writes and replace the simple_write_to_buffer() with
copy_from_user().
Fixes: 578b881ba9 ("NTB: Add tool test client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0097ae5f7a ]
When the function IS_ALIGNED() returns false, the value of ret is 0.
So, we set ret to -EINVAL to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_perf.c:602 perf_setup_inbuf() warn: missing error
code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 319f83ac98 ]
When the value of nm->isr_ctx is false, the value of ret is 0.
So, we set ret to -ENOMEM to indicate this error.
Clean up smatch warning:
drivers/ntb/test/ntb_msi_test.c:373 ntb_msit_probe() warn: missing
error code 'ret'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44a0a3c179 ]
The related system resources were not released when pci_set_dma_mask(),
pci_set_consistent_dma_mask(), or pci_iomap() return error in the
amd_ntb_init_pci() function. Add pci_release_regions() to fix it.
Fixes: a1b3695820 ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Kaige Li <likaige@loongson.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34d8673a01 ]
When running ntb_test, the script tries to run the ntb_perf test
immediately after probing the modules. Since adding multi-port support,
this fails seeing the new initialization procedure in ntb_perf
can not complete instantly.
To fix this we add a completion which is waited on when a test is
started. In this way, run can be written any time after the module is
loaded and it will wait for the initialization to complete instead of
sending an error.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b54369a248 ]
Legacy drivers do not have port numbers (but is reliably only two ports)
and was broken by the recent commit that added mult-port support to
ntb_perf. This is especially important to support the cross link
topology which is perfectly symmetric and cannot assign unique port
numbers easily.
Hardware that returns zero for both the local port and the peer should
just always use gidx=0 for the only peer.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9c4211ac9 ]
ntb_perf should not require more than one memory window per peer. This
was probably an off-by-one error.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40da7d9a93 ]
Commit 417cf39cfe ("NTB: Set dma mask and dma coherent mask to NTB
devices") started using the NTB device for DMA allocations which was
turns out was wrong. If the IOMMU is enabled, such alloctanions will
always fail with messages such as:
DMAR: Allocating domain for 0000:02:00.1 failed
This is because the IOMMU has not setup the device for such use.
Change the tools back to using the PCI device for allocations seeing
it doesn't make sense to add an IOMMU group for the non-physical NTB
device. Also remove the code that sets the DMA mask as it no longer
makes sense to do this.
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 912e12813d ]
When running ntb_test this warning is issued:
./ntb_test.sh: line 200: warning: command substitution: ignored null
byte in input
This is caused by the kernel returning one more byte than is necessary
when reading the link file.
Reduce the number of bytes read back to 2 as it was before the
commit that regressed this.
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 433efe7206 ]
Currently, ntb->dev is passed to dma_alloc_coherent
and dma_free_coherent calls. The returned dma_addr_t
is the CPU physical address. This works fine as long
as IOMMU is disabled. But when IOMMU is enabled, we
need to make sure that IOVA is returned for dma_addr_t.
So the correct way to achieve this is by changing the
first parameter of dma_alloc_coherent() as ntb->pdev->dev
instead.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98f4e14026 ]
Currently, ntb->dev is passed to dma_alloc_coherent
and dma_free_coherent calls. The returned dma_addr_t
is the CPU physical address. This works fine as long
as IOMMU is disabled. But when IOMMU is enabled, we
need to make sure that IOVA is returned for dma_addr_t.
So the correct way to achieve this is by changing the
first parameter of dma_alloc_coherent() as ntb->pdev->dev
instead.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8b086d9d ]
When the commit adding ntb_default_port_number() and
ntb_default_peer_port_number() entered the kernel there was no
users of it so it was impossible to tell what the API needed.
When a user finally landed a year later (ntb_pingpong) there were
more NTB topologies were created and no consideration was considered
to how other drivers had changed.
Now that there is a user it can be fixed to provide a sensible default
for the legacy drivers that do not implement ntb_{peer_}port_number().
Seeing ntb_pingpong doesn't check error codes returning EINVAL was also
not sensible.
Patches for ntb_pingpong and ntb_perf follow (which are broken
otherwise) to support hardware that doesn't have port numbers. This is
important not only to not break support with existing drivers but for
the cross link topology which, due to its perfect symmetry, cannot
assign unique port numbers to each side.
Fixes: 1e5301196a ("NTB: Add indexed ports NTB API")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca93c45755 ]
This commit fixes pingpong support for existing drivers that do not
implement ntb_default_port_number() and ntb_default_peer_port_number().
This is required for hardware (like the crosslink topology of
switchtec) which cannot assign reasonable port numbers to each port due
to its perfect symmetry.
Instead of picking the doorbell to use based on the the index of the
peer, we use the peer's port number. This is a bit clearer and easier
to understand.
Fixes: c7aeb0afdc ("NTB: ntb_pp: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The AMD new hardware uses BAR23 and BAR45 as memory windows
as compared to previos where BAR1, BAR23 and BAR45 is used
for memory windows.
This patch add support for both AMD hardwares.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Variable rc is initialized to a value that is never read and it
is re-assigned later. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On switchtec_ntb_mw_set_trans() call, when (only) address == 0, it acts as
ntb_mw_clear_trans(). Fix this, since address == 0 and size != 0 is valid
combination for setting translation.
Signed-off-by: Alexander Fomichev <fomichev.ru@gmail.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
second parameter of ntb_peer_mw_get_addr is pointing to wrong memory
window index by passing "peer gidx" instead of "local gidx".
For ex, "local gidx" value is '0' and "peer gidx" value is '1', then
on peer side ntb_mw_set_trans() api is used as below with gidx pointing to
local side gidx which is '0', so memroy window '0' is chosen and XLAT '0'
will be programmed by peer side.
ntb_mw_set_trans(perf->ntb, peer->pidx, peer->gidx, peer->inbuf_xlat,
peer->inbuf_size);
Now, on local side ntb_peer_mw_get_addr() is been used as below with gidx
pointing to "peer gidx" which is '1', so pointing to memory window '1'
instead of memory window '0'.
ntb_peer_mw_get_addr(perf->ntb, peer->gidx, &phys_addr,
&peer->outbuf_size);
So this patch pass "local gidx" as parameter to ntb_peer_mw_get_addr().
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
Introduce the module parameter 'use_msi' which, when set, uses
MSI interrupts instead of doorbells for each queue pair (QP). The
parameter is only available if NTB MSI support is configured into
the kernel. We also require there to be more than one memory window
(MW) so that an extra one is available to forward the APIC region.
To use MSIs, we request one interrupt per QP and forward the MSI address
and data to the peer using scratch pad registers (SPADS) above the MW
SPADS. (If there are not enough SPADS the MSI interrupt will not be used.)
Once registered, we simply use ntb_msi_peer_trigger and the receiving
ISR simply queues up the rxc_db_work for the queue.
This addition can significantly improve performance of ntb_transport.
In a simple, untuned, apples-to-apples comparision using ntb_netdev
and iperf with switchtec hardware, I see 3.88Gb/s without MSI
interrupts and 14.1Gb/s wit MSI, which is a more than 3x improvement.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Introduce a tool to test NTB MSI interrupts similar to the other
NTB test tools. This tool creates a debugfs directory for each
NTB device with the following files:
port
irqX_occurrences
peerX/port
peerX/count
peerX/trigger
The 'port' file tells the user the local port number and the
'occurrences' files tell the number of local interrupts that
have been received for each interrupt.
For each peer, the 'port' file and the 'count' file tell you the
peer's port number and number of interrupts respectively. Writing
the interrupt number to the 'trigger' file triggers the interrupt
handler for the peer which should increment their corresponding
'occurrences' file. The 'ready' file indicates if a peer is ready,
writing to this file blocks until it is ready.
The module parameter num_irqs can be used to set the number of
local interrupts. By default this is 4. This is only limited by
the number of unused MSI interrupts registered by the hardware
(this will require support of the hardware driver) and there must
be at least 2*num_irqs + 1 spads registers available.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The NTB MSI library allows passing MSI interrupts across a memory
window. This offers similar functionality to doorbells or messages
except will often have much better latency and the client can
potentially use significantly more remote interrupts than typical hardware
provides for doorbells. (Which can be important in high-multiport
setups.)
The library utilizes one memory window per peer and uses the highest
index memory windows. Before any ntb_msi function may be used, the user
must call ntb_msi_init(). It may then setup and tear down the memory
windows when the link state changes using ntb_msi_setup_mws() and
ntb_msi_clear_mws().
The peer which receives the interrupt must call ntb_msim_request_irq()
to assign the interrupt handler (this function is functionally
similar to devm_request_irq()) and the returned descriptor must be
transferred to the peer which can use it to trigger the interrupt.
The triggering peer, once having received the descriptor, can
trigger the interrupt by calling ntb_msi_peer_trigger().
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The kbuild system does not support having multiple source files in
a module if one of those source files has the same name as the module.
Therefore, we must rename ntb.c to core.c, while the module remains
ntb.ko.
This is similar to the way the nvme modules are structured.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Switchtec does not support setting multiple MWs simultaneously. The
driver takes a hardware lock to ensure that two peers are not doing this
simultaneously and it fails if someone else takes the lock. In most
cases, this is fine as clients only setup the MWs once on one side of
the link.
However, there's a race condition when a re-initialization is caused by
a link event. The driver will re-setup the shared memory window
asynchronously and this races with the client setting up it's memory
windows on the link up event.
To fix this we ensure do the entire initialization in a work queue and
signal the client once it's done.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In case of NTB crosslink topology, the setting of shared memory window in
the virtual partition doesn't reset on peer's reboot. So skip the
unnecessary re-setup of shared memory window for that case.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When a re-initialization is caused by a link event, the driver will
re-setup the shared memory window. But at that time, the shared memory
is still valid, and it's unnecessary to free, reallocate and then
initialize it again. We only need to reconfigure the hardware
registers. Remove the redundant steps from
switchtec_ntb_reinit_peer() function.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This code triggers a Smatch warning:
drivers/ntb/hw/amd/ntb_hw_amd.c:336 amd_ntb_db_vector_mask()
warn: should '(1 << db_vector)' be a 64 bit type?
I don't think "db_vector" can be higher than 16 so this doesn't affect
runtime, but it's nice to silence the static checker warning and we
might increase "ndev->db_count" in the future.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This code triggers a Smatch warning:
drivers/ntb/hw/mscc/ntb_hw_switchtec.c:884 switchtec_ntb_init_sndev()
warn: should '(1 << sndev->peer_partition)' be a 64 bit type?
The "part_map" and "tpart_vec" variables are u64 type so this seems like
a valid warning.
Fixes: 3df54c870f ("ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setups")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Dan Carpenter's static checker reported:
drivers/ntb/ntb_transport.c:1926 ntb_transport_create_queue()
error: we previously assumed 'qp->tx_dma_chan' could be null (see line 1872)
This is because the tx_mw_dma_addr is uninitialized in this function and
may be incorrectly released using a NULL DMA channel.
In practice this bug will not likely be seen. I'd guess you could hit
this if you loaded ntb_netdev with use_dma=True, then unloaded it and
loaded it again after setting the module parameter to use_dma=False.
To fix this, we simply ensure that tx_mw_dma_addr is always
initialized to zero. This is the safest in case any other part of the
code operates on it if it is non-zero.
Fixes: c59666bb32 ("NTB: ntb_transport: Ensure the destination buffer is mapped for TX DMA")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
when ntb_perf is unloaded, the command scratchpad register still
retains the last initialized value of PERF_CMD_INVAL. When ntb_perf
is re-loaded and reads peer command scratchpad register and it mis
interprets the peer state as initialized.
To avoid this, clearing the local side command scratchpad register
in perf_disable_service
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If ntb link disabled before clearing peer's XLAT register, the clearing
won't have any effect since the link is already down. So modified the
sequence so that the link is down only towards the end of the function
after clearing the XLAT register
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
while waiting for the peer ntb_perf to initialize scratchpad
registers, local side ntb_perf might have already exhausted the
maximum number of retries which is currently set to 500. To avoid
this and to give little more time to the peer ntb_perf for scratchpad
initialization, increased the number of retries to 1000
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
