Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for some reported issues.
Included in here is:
- much reported rust_binder fix
- counter driver fixes
- new device ids for the mei driver
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
rust_binder: remove spin_lock() in rust_shrink_free_page()
mei: me: add nova lake point S DID
counter: 104-quad-8: Fix incorrect return value in IRQ handler
counter: interrupt-cnt: Drop IRQF_NO_THREAD flag
Pull SoC fixes from Arnd Bergmann:
"The main code change is a revert of the Raspberry Pi RP1 overlay
support that was decided to not be ready.
The other fixes are all for devicetree sources:
- ethernet configuration on ixp42x-actiontec-mi424wr is board
revision specific
- validation warning fixes for imx27/imx51/imx6, hikey960 and k3
- Minor corrections across imx8 boards, addressing all types of
issues with interrups, dma, ethernet and clock settings, all simple
one-line changes"
* tag 'soc-fixes-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
arm64: dts: hisilicon: hikey960: Drop "snps,gctl-reset-quirk" and "snps,tx_de_emphasis*" properties
Documentation/process: maintainer-soc: Mark 'make' as commands
Documentation/process: maintainer-soc: Be more explicit about defconfig
arm64: dts: mba8mx: Fix Ethernet PHY IRQ support
arm64: dts: imx8qm-ss-dma: correct the dma channels of lpuart
arm64: dts: imx8mp: Fix LAN8740Ai PHY reference clock on DH electronics i.MX8M Plus DHCOM
arm64: dts: freescale: tx8p-ml81: fix eqos nvmem-cells
arm64: dts: freescale: moduline-display: fix compatible
dt-bindings: arm: fsl: moduline-display: fix compatible
ARM: dts: imx6q-ba16: fix RTC interrupt level
arm64: dts: freescale: imx95-toradex-smarc: fix SMARC_SDIO_WP label position
arm64: dts: freescale: imx95-toradex-smarc: use edge trigger for ethphy1 interrupt
arm64: dts: add off-on-delay-us for usdhc2 regulator
arm64: dts: imx8qm-mek: correct the light sensor interrupt type to low level
ARM: dts: nxp: imx: Fix mc13xxx LED node names
arm64: dts: imx95: correct I3C2 pclk to IMX95_CLK_BUSWAKEUP
MAINTAINERS: Fix a linusw mail address
arm64: dts: broadcom: rp1: drop RP1 overlay
arm64: dts: broadcom: bcm2712: fix RP1 endpoint PCI topology
misc: rp1: drop overlay support
...
The RP1 driver can load an overlay at runtime to describe the inner
peripherals. This has led to a lot of confusion regarding the naming
of nodes, their topology and the reclaiming of related node resources.
Since the overlay is currently not fully functional, drop its support
in the driver in favor of the fully described static DT.
This also means that this driver does not depend on CONFIG_PCI_DYNAMIC_OF_NODES
and no longer requires PCI quirks to dynamically create the intermediate
PCI nodes.
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/4b0aa7160877cf128b9bc713776bcac73c46eb24.1766077285.git.andrea.porta@suse.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Since commit eb972eab07 ("lkdtm/bugs: Add cases for BUG and PANIC
occurring in hardirq context"), building with clang for x86_64 results
in the following warnings:
vmlinux.o: warning: objtool: lkdtm_PANIC_IN_HARDIRQ(): unexpected end of section .text.lkdtm_PANIC_IN_HARDIRQ
vmlinux.o: warning: objtool: lkdtm_BUG_IN_HARDIRQ(): unexpected end of section .text.lkdtm_BUG_IN_HARDIRQ
caused by busy "while (wait_for_...);" loops. Add READ_ONCE() and
cpu_relax() to better indicate the intention and avoid any unwanted
compiler optimisations.
Fixes: eb972eab07 ("lkdtm/bugs: Add cases for BUG and PANIC occurring in hardirq context")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512190111.jxFSqxUH-lkp@intel.com/
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add lkdtm cases to trigger a BUG() or panic() from hardirq context. This
is useful for testing pstore behavior being invoked from such contexts.
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull SCSI fixes from James Bottomley:
"The only core fix is in doc; all the others are in drivers, with the
biggest impacts in libsas being the rollback on error handling and in
ufs coming from a couple of error handling fixes, one causing a crash
if it's activated before scanning and the other fixing W-LUN
resumption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom: Fix confusing cleanup.h syntax
scsi: libsas: Add rollback handling when an error occurs
scsi: device_handler: Return error pointer in scsi_dh_attached_handler_name()
scsi: ufs: core: Fix a deadlock in the frequency scaling code
scsi: ufs: core: Fix an error handler crash
scsi: Revert "scsi: libsas: Fix exp-attached device scan after probe failure scanned in again after probe failed"
scsi: ufs: core: Fix RPMB link error by reversing Kconfig dependencies
scsi: qla4xxx: Use time conversion macros
scsi: qla2xxx: Enable/disable IRQD_NO_BALANCING during reset
scsi: ipr: Enable/disable IRQD_NO_BALANCING during reset
scsi: imm: Fix use-after-free bug caused by unfinished delayed work
scsi: target: sbp: Remove KMSG_COMPONENT macro
scsi: core: Correct documentation for scsi_device_quiesce()
scsi: mpi3mr: Prevent duplicate SAS/SATA device entries in channel 1
scsi: target: Reset t_task_cdb pointer in error case
scsi: ufs: core: Fix EH failure after W-LUN resume error
Pull char/misc/IIO driver updates from Greg KH:
"Here is the big set of char/misc/iio driver updates for 6.19-rc1. Lots
of stuff in here including:
- lots of IIO driver updates, cleanups, and additions
- large interconnect driver changes as they get converted over to a
dynamic system of ids
- coresight driver updates
- mwave driver updates
- binder driver updates and changes
- comedi driver fixes now that the fuzzers are being set loose on
them
- nvmem driver updates
- new uio driver addition
- lots of other small char/misc driver updates, full details in the
shortlog
All of these have been in linux-next for a while now"
* tag 'char-misc-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (304 commits)
char: applicom: fix NULL pointer dereference in ac_ioctl
hangcheck-timer: fix coding style spacing
hangcheck-timer: Replace %Ld with %lld
hangcheck-timer: replace printk(KERN_CRIT) with pr_crit
uio: Add SVA support for PCI devices via uio_pci_generic_sva.c
dt-bindings: slimbus: fix warning from example
intel_th: Fix error handling in intel_th_output_open
misc: rp1: Fix an error handling path in rp1_probe()
char: xillybus: add WQ_UNBOUND to alloc_workqueue users
misc: bh1770glc: use pm_runtime_resume_and_get() in power_state_store
misc: cb710: Fix a NULL vs IS_ERR() check in probe()
mux: mmio: Add suspend and resume support
virt: acrn: split acrn_mmio_dev_res out of acrn_mmiodev
greybus: gb-beagleplay: Fix timeout handling in bootloader functions
greybus: add WQ_PERCPU to alloc_workqueue users
char/mwave: drop typedefs
char/mwave: drop printk wrapper
char/mwave: remove printk tracing
char/mwave: remove unneeded fops
char/mwave: remove MWAVE_FUTZ_WITH_OTHER_DEVICES ifdeffery
...
Pull SCSI updates from James Bottomley:
"Usual driver updates (ufs, lpfc, target, qla2xxx) plus assorted
cleanups and fixes including the WQ_PERCPU series.
The biggest core change is the new allocation of pseudo-devices which
allow the sending of internal commands to a given SCSI target"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (147 commits)
scsi: MAINTAINERS: Add the UFS include directory
scsi: scsi_debug: Support injecting unaligned write errors
scsi: qla2xxx: Fix improper freeing of purex item
scsi: ufs: rockchip: Fix compile error without CONFIG_GPIOLIB
scsi: ufs: rockchip: Reset controller on PRE_CHANGE of hce enable notify
scsi: ufs: core: Use scsi_device_busy()
scsi: ufs: core: Fix single doorbell mode support
scsi: pm80xx: Add WQ_PERCPU to alloc_workqueue() users
scsi: target: Add WQ_PERCPU to alloc_workqueue() users
scsi: qedi: Add WQ_PERCPU to alloc_workqueue() users
scsi: target: ibmvscsi: Add WQ_PERCPU to alloc_workqueue() users
scsi: qedf: Add WQ_PERCPU to alloc_workqueue() users
scsi: bnx2fc: Add WQ_PERCPU to alloc_workqueue() users
scsi: be2iscsi: Add WQ_PERCPU to alloc_workqueue() users
scsi: message: fusion: Add WQ_PERCPU to alloc_workqueue() users
scsi: lpfc: WQ_PERCPU added to alloc_workqueue() users
scsi: scsi_transport_fc: WQ_PERCPU added to alloc_workqueue users()
scsi: scsi_dh_alua: WQ_PERCPU added to alloc_workqueue() users
scsi: qla2xxx: WQ_PERCPU added to alloc_workqueue() users
scsi: target: sbp: Replace use of system_unbound_wq with system_dfl_wq
...
Pull persistent dentry infrastructure and conversion from Al Viro:
"Some filesystems use a kinda-sorta controlled dentry refcount leak to
pin dentries of created objects in dcache (and undo it when removing
those). A reference is grabbed and not released, but it's not actually
_stored_ anywhere.
That works, but it's hard to follow and verify; among other things, we
have no way to tell _which_ of the increments is intended to be an
unpaired one. Worse, on removal we need to decide whether the
reference had already been dropped, which can be non-trivial if that
removal is on umount and we need to figure out if this dentry is
pinned due to e.g. unlink() not done. Usually that is handled by using
kill_litter_super() as ->kill_sb(), but there are open-coded special
cases of the same (consider e.g. /proc/self).
Things get simpler if we introduce a new dentry flag
(DCACHE_PERSISTENT) marking those "leaked" dentries. Having it set
claims responsibility for +1 in refcount.
The end result this series is aiming for:
- get these unbalanced dget() and dput() replaced with new primitives
that would, in addition to adjusting refcount, set and clear
persistency flag.
- instead of having kill_litter_super() mess with removing the
remaining "leaked" references (e.g. for all tmpfs files that hadn't
been removed prior to umount), have the regular
shrink_dcache_for_umount() strip DCACHE_PERSISTENT of all dentries,
dropping the corresponding reference if it had been set. After that
kill_litter_super() becomes an equivalent of kill_anon_super().
Doing that in a single step is not feasible - it would affect too many
places in too many filesystems. It has to be split into a series.
This work has really started early in 2024; quite a few preliminary
pieces have already gone into mainline. This chunk is finally getting
to the meat of that stuff - infrastructure and most of the conversions
to it.
Some pieces are still sitting in the local branches, but the bulk of
that stuff is here"
* tag 'pull-persistency' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
d_make_discardable(): warn if given a non-persistent dentry
kill securityfs_recursive_remove()
convert securityfs
get rid of kill_litter_super()
convert rust_binderfs
convert nfsctl
convert rpc_pipefs
convert hypfs
hypfs: swich hypfs_create_u64() to returning int
hypfs: switch hypfs_create_str() to returning int
hypfs: don't pin dentries twice
convert gadgetfs
gadgetfs: switch to simple_remove_by_name()
convert functionfs
functionfs: switch to simple_remove_by_name()
functionfs: fix the open/removal races
functionfs: need to cancel ->reset_work in ->kill_sb()
functionfs: don't bother with ffs->ref in ffs_data_{opened,closed}()
functionfs: don't abuse ffs_data_closed() on fs shutdown
convert selinuxfs
...
When CONFIG_SCSI_UFSHCD=y and CONFIG_RPMB=m, the kernel fails to link
with undefined references to ufs_rpmb_probe() and ufs_rpmb_remove():
ld: drivers/ufs/core/ufshcd.c:8950: undefined reference to `ufs_rpmb_probe'
ld: drivers/ufs/core/ufshcd.c:10505: undefined reference to `ufs_rpmb_remove'
The issue is that RPMB depends on its consumers (MMC, UFS) in Kconfig,
which is backwards. This prevents proper module dependency handling when
the library is modular but consumers are built-in.
Fix by reversing the dependency:
- Remove 'depends on MMC || SCSI_UFSHCD' from RPMB Kconfig
- Add 'depends on RPMB || !RPMB' to SCSI_UFSHCD Kconfig
This allows RPMB to be an independent library while ensuring correct
linking in all module/built-in combinations.
Fixes: b06b8c4214 ("scsi: ufs: core: Add OP-TEE based RPMB driver for UFS devices")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511300443.h7sotuL0-lkp@intel.com/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20251202155138.2607210-1-beanhuo@iokpp.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull fd prepare updates from Christian Brauner:
"This adds the FD_ADD() and FD_PREPARE() primitive. They simplify the
common pattern of get_unused_fd_flags() + create file + fd_install()
that is used extensively throughout the kernel and currently requires
cumbersome cleanup paths.
FD_ADD() - For simple cases where a file is installed immediately:
fd = FD_ADD(O_CLOEXEC, vfio_device_open_file(device));
if (fd < 0)
vfio_device_put_registration(device);
return fd;
FD_PREPARE() - For cases requiring access to the fd or file, or
additional work before publishing:
FD_PREPARE(fdf, O_CLOEXEC, sync_file->file);
if (fdf.err) {
fput(sync_file->file);
return fdf.err;
}
data.fence = fd_prepare_fd(fdf);
if (copy_to_user((void __user *)arg, &data, sizeof(data)))
return -EFAULT;
return fd_publish(fdf);
The primitives are centered around struct fd_prepare. FD_PREPARE()
encapsulates all allocation and cleanup logic and must be followed by
a call to fd_publish() which associates the fd with the file and
installs it into the caller's fdtable. If fd_publish() isn't called,
both are deallocated automatically. FD_ADD() is a shorthand that does
fd_publish() immediately and never exposes the struct to the caller.
I've implemented this in a way that it's compatible with the cleanup
infrastructure while also being usable separately. IOW, it's centered
around struct fd_prepare which is aliased to class_fd_prepare_t and so
we can make use of all the basica guard infrastructure"
* tag 'vfs-6.19-rc1.fd_prepare.fs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (42 commits)
io_uring: convert io_create_mock_file() to FD_PREPARE()
file: convert replace_fd() to FD_PREPARE()
vfio: convert vfio_group_ioctl_get_device_fd() to FD_ADD()
tty: convert ptm_open_peer() to FD_ADD()
ntsync: convert ntsync_obj_get_fd() to FD_PREPARE()
media: convert media_request_alloc() to FD_PREPARE()
hv: convert mshv_ioctl_create_partition() to FD_ADD()
gpio: convert linehandle_create() to FD_PREPARE()
pseries: port papr_rtas_setup_file_interface() to FD_ADD()
pseries: convert papr_platform_dump_create_handle() to FD_ADD()
spufs: convert spufs_gang_open() to FD_PREPARE()
papr-hvpipe: convert papr_hvpipe_dev_create_handle() to FD_PREPARE()
spufs: convert spufs_context_open() to FD_PREPARE()
net/socket: convert __sys_accept4_file() to FD_ADD()
net/socket: convert sock_map_fd() to FD_ADD()
net/kcm: convert kcm_ioctl() to FD_PREPARE()
net/handshake: convert handshake_nl_accept_doit() to FD_PREPARE()
secretmem: convert memfd_secret() to FD_ADD()
memfd: convert memfd_create() to FD_ADD()
bpf: convert bpf_token_create() to FD_PREPARE()
...
pm_runtime_get_sync() may increment the runtime PM usage count even if the
resume fails, which requires an explicit pm_runtime_put_noidle() to balance
it. This driver ignored the return value, risking a usage-count leak on
resume failure.
Replace it with pm_runtime_resume_and_get(), which returns 0 on success and
a negative errno on failure, and only increments the usage count on success.
This simplifies the error path and avoids possible leaks. Also check for
errors explicitly with `if (ret < 0)`.
Signed-off-by: Vivek BalachandharTN <vivek.balachandhar@gmail.com>
Link: https://patch.msgid.link/20251030120022.239951-1-vivek.balachandhar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_register() fails to release the device reference in error paths
after device_initialize(). During normal device registration, the
reference is properly handled through mei_deregister() which calls
device_destroy(). However, in error handling paths (such as cdev_alloc
failure, cdev_add failure, etc.), missing put_device() calls cause
reference count leaks, preventing the device's release function
(mei_device_release) from being called and resulting in memory leaks
of mei_device.
Found by code review.
Cc: stable <stable@kernel.org>
Fixes: 7704e6be4e ("mei: hook mei_device on class device")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Acked-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://patch.msgid.link/20251104020133.5017-1-make24@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
static contents for each "service processor", whatever the fuck it is.
Congruent subdirectories of root, created at mount time, taken out
by kill_litter_super(). All dentries created with d_alloc_name() and are
left pinned. The odd part is that the list of service providers is
assumed to be unchanging - no locking, nothing to handle removals or
extra elements added later on.
... and it's a PCI device. If you ever tell it to remove an instance,
you are fucked - it doesn't bother with removing its directory from filesystem,
it has a strange check that presumably wanted to be a check for removed
devices, but it had never been fleshed out.
Anyway, d_add() -> d_make_persistent()+dput() in ibmasmfs_create_dir() and
ibmasmfs_create_file(), and make the latter return int - no need to even
borrow that dentry, callers completely ignore it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add OP-TEE based RPMB support for UFS devices. This enables secure RPMB
operations on UFS devices through OP-TEE, providing the same
functionality available for eMMC devices and extending kernel-based
secure storage support to UFS-based systems.
Benefits of OP-TEE based RPMB implementation:
- Eliminates dependency on userspace supplicant for RPMB access
- Enables early boot secure storage access (e.g., fTPM, secure UEFI
variables)
- Provides kernel-level RPMB access as soon as UFS driver is
initialized
- Removes complex initramfs dependencies and boot ordering requirements
- Ensures reliable and deterministic secure storage operations
- Supports both built-in and modular fTPM configurations
[mkp: make this build as a module]
Co-developed-by: Can Guo <can.guo@oss.qualcomm.com>
Signed-off-by: Can Guo <can.guo@oss.qualcomm.com>
Reviewed-by: Avri Altman <avri.altman@sandisk.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://patch.msgid.link/20251107230518.4060231-4-beanhuo@iokpp.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need the fixes in here, and it resolves a merge conflict in:
drivers/misc/amd-sbi/Kconfig
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc/android driver fixes for 6.18-rc3 for
reported issues. Included in here are:
- rust binder fixes for reported issues
- mei device id addition
- mei driver fixes
- comedi bugfix
- most usb driver bugfixes
- fastrpc memory leak fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
most: usb: hdm_probe: Fix calling put_device() before device initialization
most: usb: Fix use-after-free in hdm_disconnect
binder: remove "invalid inc weak" check
mei: txe: fix initialization order
comedi: fix divide-by-zero in comedi_buf_munge()
mei: late_bind: Fix -Wincompatible-function-pointer-types-strict
misc: fastrpc: Fix dma_buf object leak in fastrpc_map_lookup
mei: me: add wildcat lake P DID
misc: amd-sbi: Clarify that this is a BMC driver
nvmem: rcar-efuse: add missing MODULE_DEVICE_TABLE
binder: Fix missing kernel-doc entries in binder.c
rust_binder: report freeze notification only when fully frozen
rust_binder: don't delete FreezeListener if there are pending duplicates
rust_binder: freeze_notif_done should resend if wrong state
rust_binder: remove warning about orphan mappings
rust_binder: clean `clippy::mem_replace_with_default` warning
Pull hotfixes from Andrew Morton:
"17 hotfixes. 12 are cc:stable and 14 are for MM.
There's a two-patch DAMON series from SeongJae Park which addresses a
missed check and possible memory leak. Apart from that it's all
singletons - please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-10-22-12-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
csky: abiv2: adapt to new folio flags field
mm/damon/core: use damos_commit_quota_goal() for new goal commit
mm/damon/core: fix potential memory leak by cleaning ops_filter in damon_destroy_scheme
hugetlbfs: move lock assertions after early returns in huge_pmd_unshare()
vmw_balloon: indicate success when effectively deflating during migration
mm/damon/core: fix list_add_tail() call on damon_call()
mm/mremap: correctly account old mapping after MREMAP_DONTUNMAP remap
mm: prevent poison consumption when splitting THP
ocfs2: clear extent cache after moving/defragmenting extents
mm: don't spin in add_stack_record when gfp flags don't allow
dma-debug: don't report false positives with DMA_BOUNCE_UNALIGNED_KMALLOC
mm/damon/sysfs: dealloc commit test ctx always
mm/damon/sysfs: catch commit test ctx alloc failure
hung_task: fix warnings caused by unaligned lock pointers
When building with -Wincompatible-function-pointer-types-strict, a
warning designed to catch kernel control flow integrity (kCFI) issues at
build time, there is an instance in the new mei late binding code
originating from the type parameter of mei_lb_push_payload():
drivers/misc/mei/mei_lb.c:211:18: error: incompatible function pointer types initializing 'int (*)(struct device *, u32, u32, const void *, size_t)' (aka 'int (*)(struct device *, unsigned int, unsigned int, const void *, unsigned long)') with an expression of type 'int (struct device *, enum intel_lb_type, u32, const void *, size_t)' (aka 'int (struct device *, enum intel_lb_type, unsigned int, const void *, unsigned long)') [-Werror,-Wincompatible-function-pointer-types-strict]
211 | .push_payload = mei_lb_push_payload,
| ^~~~~~~~~~~~~~~~~~~
While 'unsigned int' and 'enum intel_lb_type' are ABI compatible, hence
no regular warning from -Wincompatible-function-pointer-types, the
mismatch will trigger a kCFI violation when mei_lb_push_payload() is
called indirectly.
Update the type parameter of mei_lb_push_payload() to be 'u32' to match
the prototype in 'struct intel_lb_component_ops', clearing up the
warning and kCFI violation.
Fixes: 741eeabb7c ("mei: late_bind: add late binding component driver")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20250920-drm-xe-fix-wifpts-v1-1-c89b5357c7ba@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- MCAMSR protocol for revision 0x21 is updated to include the
extended thread supported by the platform.
- This modifies the existing protocol to include additional byte
to provide high thread number.
- New input structure is defined to address this, as the hardware
protocol is tightly coupled with the input structure length
Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com>
Signed-off-by: Akshay Gupta <akshay.gupta@amd.com>
Link: https://patch.msgid.link/20250915103649.1705078-6-akshay.gupta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- CPUID protocol for revision 0x21 is updated to include the
extended thread supported by the platform.
- This modifies the existing protocol to include additional byte
to provide high thread number.
- New input structure is defined to address this, as the hardware
protocol is tightly coupled with the input structure length
Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com>
Signed-off-by: Akshay Gupta <akshay.gupta@amd.com>
Link: https://patch.msgid.link/20250915103649.1705078-5-akshay.gupta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- RMI registers addresses in AMD new platforms are 2 bytes,
on previous processors the address size is 1 byte.
- Implement logic to identify register address size at runtime.
- The identification is done in first transaction using the
Revision register.
- The revision register can be read using 1 byte in both, older and
newer platforms.
- However, sending 1 byte on later platform can cause unrecoverable error.
Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com>
Signed-off-by: Akshay Gupta <akshay.gupta@amd.com>
Link: https://patch.msgid.link/20250915103649.1705078-3-akshay.gupta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD EPYC platforms with zen5 and later support APML(SB-RMI)
connection to the BMC over I3C bus for faster data transfer
up to 12.5 Mhz.
I2C and I3C is supported in same file using module_i3c_i2c_driver()
with probe based on dts entry.
AMD APML I3C devices support static address for backward compatibility to I2C.
I3C static address can be used to assign I3C device dynamic address.
Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com>
Signed-off-by: Akshay Gupta <akshay.gupta@amd.com>
Link: https://patch.msgid.link/20250915103649.1705078-2-akshay.gupta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When migrating a balloon page, we first deflate the old page to then
inflate the new page.
However, if inflating the new page succeeded, we effectively deflated the
old page, reducing the balloon size.
In that case, the migration actually worked: similar to migrating+
immediately deflating the new page. The old page will be freed back to
the buddy.
Right now, the core will leave the page be marked as isolated (as we
returned an error). When later trying to putback that page, we will run
into the WARN_ON_ONCE() in balloon_page_putback().
That handling was changed in commit 3544c4facc ("mm/balloon_compaction:
stop using __ClearPageMovable()"); before that change, we would have
tolerated that way of handling it.
To fix it, let's just return 0 in that case, making the core effectively
just clear the "isolated" flag + freeing it back to the buddy as if the
migration succeeded. Note that the new page will also get freed when the
core puts the last reference.
Note that this also makes it all be more consistent: we will no longer
unisolate the page in the balloon driver while keeping it marked as being
isolated in migration core.
This was found by code inspection.
Link: https://lkml.kernel.org/r/20251014124455.478345-1-david@redhat.com
Fixes: 3544c4facc ("mm/balloon_compaction: stop using __ClearPageMovable()")
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Jerrin Shaji George <jerrin.shaji-george@broadcom.com>
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit cc0cc23bab ("powerpc/xive: Untangle xive from child interrupt
controller drivers") changed xive_irq_data to be stashed to chip_data
instead of handler_data. However, multiple places are still attempting to
read xive_irq_data from handler_data and get a NULL pointer deference bug.
Update them to read xive_irq_data from chip_data.
Non-XIVE files which touch xive_irq_data seem quite strange to me,
especially the ocxl driver. I think there ought to be an alternative
platform-independent solution, instead of touching XIVE's data directly.
Therefore, I think this whole thing should be cleaned up. But perhaps I
just misunderstand something. In any case, this cleanup would not be
trivial; for now, just get things working again.
Fixes: cc0cc23bab ("powerpc/xive: Untangle xive from child interrupt controller drivers")
Reported-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Closes: https://lore.kernel.org/linuxppc-dev/68e48df8.170a0220.4b4b0.217d@mx.google.com/
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com> # ocxl
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20251008081359.1382699-1-namcao@linutronix.de
Pull more x86 updates from Borislav Petkov:
- Remove a bunch of asm implementing condition flags testing in KVM's
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled
kernels in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
* tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86,retpoline: Optimize patch_retpoline()
x86,ibt: Use UDB instead of 0xEA
x86/cfi: Remove __noinitretpoline and __noretpoline
x86/cfi: Add "debug" option to "cfi=" bootparam
x86/cfi: Standardize on common "CFI:" prefix for CFI reports
x86/cfi: Document the "cfi=" bootparam options
x86/traps: Clarify KCFI instruction layout
compiler_types.h: Move __nocfi out of compiler-specific header
objtool: Validate kCFI calls
x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y
x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware
x86/fred: Install system vector handlers even if FRED isn't fully enabled
x86/hyperv: Use direct call to hypercall-page
x86/hyperv: Clean up hv_do_hypercall()
KVM: x86: Remove fastops
KVM: x86: Convert em_salc() to C
KVM: x86: Introduce EM_ASM_3WCL
KVM: x86: Introduce EM_ASM_1SRC2
KVM: x86: Introduce EM_ASM_2CL
KVM: x86: Introduce EM_ASM_2W
...
Pull char/misc fixes from Greg KH:
"Here are some small nvmem and fastrpc fixes that missed the cut-off to
get into 6.17-final, due to me being slow in getting them out, my
fault, not the maintainers of these subsystems :(
Anyway, better late than never. Changes included in here are:
- nvmem fix for automatic module loading
- fastrpc driver fixes for reported issues
All of these have been in linux-next for weeks (4?) with no reported
issues"
* tag 'char-misc-6.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: fastrpc: Skip reference for DMA handles
misc: fastrpc: fix possible map leak in fastrpc_put_args
misc: fastrpc: Fix fastrpc_map_lookup operation
misc: fastrpc: Save actual DMA size in fastrpc_map structure
nvmem: layouts: fix automatic module loading
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Add PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() macros that
take config space accessor functions.
Implement pci_find_capability(), pci_find_ext_capability(), and
dwc, dwc endpoint, and cadence capability search interfaces with
them (Hans Zhang)
- Leave parent unit address 0 in 'interrupt-map' so that when we
build devicetree nodes to describe PCI functions that contain
multiple peripherals, we can build this property even when
interrupt controllers lack 'reg' properties (Lorenzo Pieralisi)
- Add a Xeon 6 quirk to disable Extended Tags and limit Max Read
Request Size to 128B to avoid a performance issue (Ilpo Järvinen)
- Add sysfs 'serial_number' file to expose the Device Serial Number
(Matthew Wood)
- Fix pci_acpi_preserve_config() memory leak (Nirmoy Das)
Resource management:
- Align m68k pcibios_enable_device() with other arches (Ilpo
Järvinen)
- Remove sparc pcibios_enable_device() implementations that don't do
anything beyond what pci_enable_resources() does (Ilpo Järvinen)
- Remove mips pcibios_enable_resources() and use
pci_enable_resources() instead (Ilpo Järvinen)
- Clean up bridge window sizing and assignment (Ilpo Järvinen),
including:
- Leave non-claimed bridge windows disabled
- Enable bridges even if a window wasn't assigned because not all
windows are required by downstream devices
- Preserve bridge window type when releasing the resource, since
the type is needed for reassignment
- Consolidate selection of bridge windows into two new
interfaces, pbus_select_window() and
pbus_select_window_for_type(), so this is done consistently
- Compute bridge window start and end earlier to avoid logging
stale information
MSI:
- Add quirk to disable MSI on RDC PCI to PCIe bridges (Marcos Del Sol
Vives)
Error handling:
- Align AER with EEH by allowing drivers to request a Bus Reset on
Non-Fatal Errors (in addition to the reset on Fatal Errors that we
already do) (Lukas Wunner)
- If error recovery fails, emit FAILED_RECOVERY uevents for the
devices, not for the bridge leading to them.
This makes them correspond to BEGIN_RECOVERY uevents (Lukas Wunner)
- Align AER with EEH by calling err_handler.error_detected()
callbacks to notify drivers if error recovery fails (Lukas Wunner)
- Align AER with EEH by restoring device error_state to
pci_channel_io_normal before the err_handler.slot_reset() callback.
This is earlier than before the err_handler.resume() callback
(Lukas Wunner)
- Emit a BEGIN_RECOVERY uevent when driver's
err_handler.error_detected() requests a reset, as well as when it
says recovery is complete or can be done without a reset (Niklas
Schnelle)
- Align s390 with AER and EEH by emitting uevents during error
recovery (Niklas Schnelle)
- Align EEH with AER and s390 by emitting BEGIN_RECOVERY,
SUCCESSFUL_RECOVERY, or FAILED_RECOVERY uevents depending on the
result of err_handler.error_detected() (Niklas Schnelle)
- Fix a NULL pointer dereference in aer_ratelimit() when ACPI GHES
error information identifies a device without an AER Capability
(Breno Leitao)
- Update error decoding and TLP Log printing for new errors in
current PCIe base spec (Lukas Wunner)
- Update error recovery documentation to match the current code
and use consistent nomenclature (Lukas Wunner)
ASPM:
- Enable all ClockPM and ASPM states for devicetree platforms, since
there's typically no firmware that enables ASPM
This is a risky change that may uncover hardware or configuration
defects at boot-time rather than when users enable ASPM via sysfs
later. Booting with "pcie_aspm=off" prevents this enabling
(Manivannan Sadhasivam)
- Remove the qcom code that enabled ASPM (Manivannan Sadhasivam)
Power management:
- If a device has already been disconnected, e.g., by a hotplug
removal, don't bother trying to resume it to D0 when detaching the
driver.
This avoids annoying "Unable to change power state from D3cold to
D0" messages (Mario Limonciello)
- Ensure devices are powered up before config reads for
'max_link_width', 'current_link_speed', 'current_link_width',
'secondary_bus_number', and 'subordinate_bus_number' sysfs files.
This prevents using invalid data (~0) in drivers or lspci and,
depending on how the PCIe controller reports errors, may avoid
error interrupts or crashes (Brian Norris)
Virtualization:
- Add rescan/remove locking when enabling/disabling SR-IOV, which
avoids list corruption on s390, where disabling SR-IOV also
generates hotplug events (Niklas Schnelle)
Peer-to-peer DMA:
- Free struct p2p_pgmap, not a member within it, in the
pci_p2pdma_add_resource() error path (Sungho Kim)
Endpoint framework:
- Document sysfs interface for BAR assignment of vNTB endpoint
functions (Jerome Brunet)
- Fix array underflow in endpoint BAR test case (Dan Carpenter)
- Skip endpoint IRQ test if the IRQ is out of range to avoid false
errors (Christian Bruel)
- Fix endpoint test case for controllers with fixed-size BARs smaller
than requested by the test (Marek Vasut)
- Restore inbound translation when disabling doorbell so the endpoint
doorbell test case can be run more than once (Niklas Cassel)
- Avoid a NULL pointer dereference when releasing DMA channels in
endpoint DMA test case (Shin'ichiro Kawasaki)
- Convert tegra194 interrupt number to MSI vector to fix endpoint
Kselftest MSI_TEST test case (Niklas Cassel)
- Reset tegra194 BARs when running in endpoint mode so the BAR tests
don't overwrite the ATU settings in BAR4 (Niklas Cassel)
- Handle errors in tegra194 BPMP transactions so we don't mistakenly
skip future PERST# assertion (Vidya Sagar)
AMD MDB PCIe controller driver:
- Update DT binding example to separate PERST# to a Root Port stanza
to make multiple Root Ports possible in the future (Sai Krishna
Musham)
- Add driver support for PERST# being described in a Root Port
stanza, falling back to the host bridge if not found there (Sai
Krishna Musham)
Freescale i.MX6 PCIe controller driver:
- Enable the 3.3V Vaux supply if available so devices can request
wakeup with either Beacon or WAKE# (Richard Zhu)
MediaTek PCIe Gen3 controller driver:
- Add optional sys clock ready time setting to avoid sys_clk_rdy
signal glitching in MT6991 and MT8196 (AngeloGioacchino Del Regno)
- Add DT binding and driver support for MT6991 and MT8196
(AngeloGioacchino Del Regno)
NVIDIA Tegra PCIe controller driver:
- When asserting PERST#, disable the controller instead of mistakenly
disabling the PLL twice (Nagarjuna Kristam)
- Convert struct tegra_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
Qualcomm PCIe controller driver:
- Select PCI Power Control Slot driver so slot voltage rails can be
turned on/off if described in Root Port devicetree node (Qiang Yu)
- Parse only PCI bridge child nodes in devicetree, skipping unrelated
nodes such as OPP (Operating Performance Points), which caused
probe failures (Krishna Chaitanya Chundru)
- Add 8.0 GT/s and 32.0 GT/s equalization settings (Ziyue Zhang)
- Consolidate Root Port 'phy' and 'reset' properties in struct
qcom_pcie_port, regardless of whether we got them from the Root
Port node or the host bridge node (Manivannan Sadhasivam)
- Fetch and map the ELBI register space in the DWC core rather than
in each driver individually (Krishna Chaitanya Chundru)
- Enable ECAM mechanism in DWC core by setting up iATU with 'CFG
Shift Feature' and use this in the qcom driver (Krishna Chaitanya
Chundru)
- Add SM8750 compatible to qcom,pcie-sm8550.yaml (Krishna Chaitanya
Chundru)
- Update qcom,pcie-x1e80100.yaml to allow fifth PCIe host on Qualcomm
Glymur, which is compatible with X1E80100 but doesn't have the
cnoc_sf_axi clock (Qiang Yu)
Renesas R-Car PCIe controller driver:
- Fix a typo that prevented correct PHY initialization (Marek Vasut)
- Add a missing 1ms delay after PWR reset assertion as required by
the V4H manual (Marek Vasut)
- Assure reset has completed before DBI access to avoid SError (Marek
Vasut)
- Fix inverted PHY initialization check, which sometimes led to
timeouts and failure to start the controller (Marek Vasut)
- Pass the correct IRQ domain to generic_handle_domain_irq() to fix a
regression when converting to msi_create_parent_irq_domain()
(Claudiu Beznea)
- Drop the spinlock protecting the PMSR register - it's no longer
required since pci_lock already serializes accesses (Marek Vasut)
- Convert struct rcar_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
SOPHGO PCIe controller driver:
- Check for existence of struct cdns_pcie.ops before using it to
allow Cadence drivers that don't need to supply ops (Chen Wang)
- Add DT binding and driver for the SOPHGO SG2042 PCIe controller
(Chen Wang)
STMicroelectronics STM32MP25 PCIe controller driver:
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which
needs it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics
STM32MP25 in host and endpoint modes (Christian Bruel)
Synopsys DesignWare PCIe controller driver:
- Add support for x16 in devicetree 'num-lanes' property (Konrad
Dybcio)
- Verify that if DT specifies a single IRQ for all eDMA channels, it
is named 'dma' (Niklas Cassel)
TI J721E PCIe driver:
- Add MODULE_DEVICE_TABLE() so driver can be autoloaded (Siddharth
Vadapalli)
- Power controller off before configuring the glue layer so the
controller latches the correct values on power-on (Siddharth
Vadapalli)
TI Keystone PCIe controller driver:
- Use devm_request_irq() so 'ks-pcie-error-irq' is freed when driver
exits with error (Siddharth Vadapalli)
- Add Peripheral Virtualization Unit (PVU), which restricts DMA from
PCIe devices to specific regions of host memory, to the ti,am65
binding (Jan Kiszka)
Xilinx NWL PCIe controller driver:
- Clear bootloader E_ECAM_CONTROL before merging in the new driver
value to avoid writing invalid values (Jani Nurminen)"
* tag 'pci-v6.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (141 commits)
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
PCI: xilinx-nwl: Fix ECAM programming
PCI: j721e: Fix incorrect error message in probe()
PCI: keystone: Use devm_request_irq() to free "ks-pcie-error-irq" on exit
dt-bindings: PCI: qcom,pcie-x1e80100: Set clocks minItems for the fifth Glymur PCIe Controller
PCI: dwc: Support 16-lane operation
PCI: Add lockdep assertion in pci_stop_and_remove_bus_device()
PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV
PCI: rcar-host: Convert struct rcar_msi mask_lock into raw spinlock
PCI: tegra194: Rename 'root_bus' to 'root_port_bus' in tegra_pcie_downstream_dev_to_D0()
PCI: tegra: Convert struct tegra_msi mask_lock into raw spinlock
PCI: rcar-gen4: Fix inverted break condition in PHY initialization
PCI: rcar-gen4: Assure reset occurs before DBI access
PCI: rcar-gen4: Add missing 1ms delay after PWR reset assertion
PCI: Set up bridge resources earlier
PCI: rcar-host: Drop PMSR spinlock
...
Pull Char/Misc/IIO/Binder updates from Greg KH:
"Here is the big set of char/misc/iio and other driver subsystem
changes for 6.18-rc1.
Loads of different stuff in here, it was a busy development cycle in
lots of different subsystems, with over 27k new lines added to the
tree.
Included in here are:
- IIO updates including new drivers, reworking of existing apis, and
other goodness in the sensor subsystems
- MEI driver updates and additions
- NVMEM driver updates
- slimbus removal for an unused driver and some other minor updates
- coresight driver updates and additions
- MHI driver updates
- comedi driver updates and fixes
- extcon driver updates
- interconnect driver additions
- eeprom driver updates and fixes
- minor UIO driver updates
- tiny W1 driver updates
But the majority of new code is in the rust bindings and additions,
which includes:
- misc driver rust binding updates for read/write support, we can now
write "normal" misc drivers in rust fully, and the sample driver
shows how this can be done.
- Initial framework for USB driver rust bindings, which are disabled
for now in the build, due to limited support, but coming in through
this tree due to dependencies on other rust binding changes that
were in here. I'll be enabling these back on in the build in the
usb.git tree after -rc1 is out so that developers can continue to
work on these in linux-next over the next development cycle.
- Android Binder driver implemented in Rust.
This is the big one, and was driving a huge majority of the rust
binding work over the past years. Right now there are two binder
drivers in the kernel, selected only at build time as to which one
to use as binder wants to be included in the system at boot time.
The binder C maintainers all agreed on this, as eventually, they
want the C code to be removed from the tree, but it will take a few
releases to get there while both are maintained to ensure that the
rust implementation is fully stable and compliant with the existing
userspace apis.
All of these have been in linux-next for a while"
* tag 'char-misc-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (320 commits)
rust: usb: keep usb::Device private for now
rust: usb: don't retain device context for the interface parent
USB: disable rust bindings from the build for now
samples: rust: add a USB driver sample
rust: usb: add basic USB abstractions
coresight: Add label sysfs node support
dt-bindings: arm: Add label in the coresight components
coresight: tnoc: add new AMBA ID to support Trace Noc V2
coresight: Fix incorrect handling for return value of devm_kzalloc
coresight: tpda: fix the logic to setup the element size
coresight: trbe: Return NULL pointer for allocation failures
coresight: Refactor runtime PM
coresight: Make clock sequence consistent
coresight: Refactor driver data allocation
coresight: Consolidate clock enabling
coresight: Avoid enable programming clock duplicately
coresight: Appropriately disable trace bus clocks
coresight: Appropriately disable programming clocks
coresight: etm4x: Support atclk
coresight: catu: Support atclk
...
Pull MM updates from Andrew Morton:
- "mm, swap: improve cluster scan strategy" from Kairui Song improves
performance and reduces the failure rate of swap cluster allocation
- "support large align and nid in Rust allocators" from Vitaly Wool
permits Rust allocators to set NUMA node and large alignment when
perforning slub and vmalloc reallocs
- "mm/damon/vaddr: support stat-purpose DAMOS" from Yueyang Pan extend
DAMOS_STAT's handling of the DAMON operations sets for virtual
address spaces for ops-level DAMOS filters
- "execute PROCMAP_QUERY ioctl under per-vma lock" from Suren
Baghdasaryan reduces mmap_lock contention during reads of
/proc/pid/maps
- "mm/mincore: minor clean up for swap cache checking" from Kairui Song
performs some cleanup in the swap code
- "mm: vm_normal_page*() improvements" from David Hildenbrand provides
code cleanup in the pagemap code
- "add persistent huge zero folio support" from Pankaj Raghav provides
a block layer speedup by optionalls making the
huge_zero_pagepersistent, instead of releasing it when its refcount
falls to zero
- "kho: fixes and cleanups" from Mike Rapoport adds a few touchups to
the recently added Kexec Handover feature
- "mm: make mm->flags a bitmap and 64-bit on all arches" from Lorenzo
Stoakes turns mm_struct.flags into a bitmap. To end the constant
struggle with space shortage on 32-bit conflicting with 64-bit's
needs
- "mm/swapfile.c and swap.h cleanup" from Chris Li cleans up some swap
code
- "selftests/mm: Fix false positives and skip unsupported tests" from
Donet Tom fixes a few things in our selftests code
- "prctl: extend PR_SET_THP_DISABLE to only provide THPs when advised"
from David Hildenbrand "allows individual processes to opt-out of
THP=always into THP=madvise, without affecting other workloads on the
system".
It's a long story - the [1/N] changelog spells out the considerations
- "Add and use memdesc_flags_t" from Matthew Wilcox gets us started on
the memdesc project. Please see
https://kernelnewbies.org/MatthewWilcox/Memdescs and
https://blogs.oracle.com/linux/post/introducing-memdesc
- "Tiny optimization for large read operations" from Chi Zhiling
improves the efficiency of the pagecache read path
- "Better split_huge_page_test result check" from Zi Yan improves our
folio splitting selftest code
- "test that rmap behaves as expected" from Wei Yang adds some rmap
selftests
- "remove write_cache_pages()" from Christoph Hellwig removes that
function and converts its two remaining callers
- "selftests/mm: uffd-stress fixes" from Dev Jain fixes some UFFD
selftests issues
- "introduce kernel file mapped folios" from Boris Burkov introduces
the concept of "kernel file pages". Using these permits btrfs to
account its metadata pages to the root cgroup, rather than to the
cgroups of random inappropriate tasks
- "mm/pageblock: improve readability of some pageblock handling" from
Wei Yang provides some readability improvements to the page allocator
code
- "mm/damon: support ARM32 with LPAE" from SeongJae Park teaches DAMON
to understand arm32 highmem
- "tools: testing: Use existing atomic.h for vma/maple tests" from
Brendan Jackman performs some code cleanups and deduplication under
tools/testing/
- "maple_tree: Fix testing for 32bit compiles" from Liam Howlett fixes
a couple of 32-bit issues in tools/testing/radix-tree.c
- "kasan: unify kasan_enabled() and remove arch-specific
implementations" from Sabyrzhan Tasbolatov moves KASAN arch-specific
initialization code into a common arch-neutral implementation
- "mm: remove zpool" from Johannes Weiner removes zspool - an
indirection layer which now only redirects to a single thing
(zsmalloc)
- "mm: task_stack: Stack handling cleanups" from Pasha Tatashin makes a
couple of cleanups in the fork code
- "mm: remove nth_page()" from David Hildenbrand makes rather a lot of
adjustments at various nth_page() callsites, eventually permitting
the removal of that undesirable helper function
- "introduce kasan.write_only option in hw-tags" from Yeoreum Yun
creates a KASAN read-only mode for ARM, using that architecture's
memory tagging feature. It is felt that a read-only mode KASAN is
suitable for use in production systems rather than debug-only
- "mm: hugetlb: cleanup hugetlb folio allocation" from Kefeng Wang does
some tidying in the hugetlb folio allocation code
- "mm: establish const-correctness for pointer parameters" from Max
Kellermann makes quite a number of the MM API functions more accurate
about the constness of their arguments. This was getting in the way
of subsystems (in this case CEPH) when they attempt to improving
their own const/non-const accuracy
- "Cleanup free_pages() misuse" from Vishal Moola fixes a number of
code sites which were confused over when to use free_pages() vs
__free_pages()
- "Add Rust abstraction for Maple Trees" from Alice Ryhl makes the
mapletree code accessible to Rust. Required by nouveau and by its
forthcoming successor: the new Rust Nova driver
- "selftests/mm: split_huge_page_test: split_pte_mapped_thp
improvements" from David Hildenbrand adds a fix and some cleanups to
the thp selftesting code
- "mm, swap: introduce swap table as swap cache (phase I)" from Chris
Li and Kairui Song is the first step along the path to implementing
"swap tables" - a new approach to swap allocation and state tracking
which is expected to yield speed and space improvements. This
patchset itself yields a 5-20% performance benefit in some situations
- "Some ptdesc cleanups" from Matthew Wilcox utilizes the new memdesc
layer to clean up the ptdesc code a little
- "Fix va_high_addr_switch.sh test failure" from Chunyu Hu fixes some
issues in our 5-level pagetable selftesting code
- "Minor fixes for memory allocation profiling" from Suren Baghdasaryan
addresses a couple of minor issues in relatively new memory
allocation profiling feature
- "Small cleanups" from Matthew Wilcox has a few cleanups in
preparation for more memdesc work
- "mm/damon: add addr_unit for DAMON_LRU_SORT and DAMON_RECLAIM" from
Quanmin Yan makes some changes to DAMON in furtherance of supporting
arm highmem
- "selftests/mm: Add -Wunreachable-code and fix warnings" from Muhammad
Anjum adds that compiler check to selftests code and fixes the
fallout, by removing dead code
- "Improvements to Victim Process Thawing and OOM Reaper Traversal
Order" from zhongjinji makes a number of improvements in the OOM
killer: mainly thawing a more appropriate group of victim threads so
they can release resources
- "mm/damon: misc fixups and improvements for 6.18" from SeongJae Park
is a bunch of small and unrelated fixups for DAMON
- "mm/damon: define and use DAMON initialization check function" from
SeongJae Park implement reliability and maintainability improvements
to a recently-added bug fix
- "mm/damon/stat: expose auto-tuned intervals and non-idle ages" from
SeongJae Park provides additional transparency to userspace clients
of the DAMON_STAT information
- "Expand scope of khugepaged anonymous collapse" from Dev Jain removes
some constraints on khubepaged's collapsing of anon VMAs. It also
increases the success rate of MADV_COLLAPSE against an anon vma
- "mm: do not assume file == vma->vm_file in compat_vma_mmap_prepare()"
from Lorenzo Stoakes moves us further towards removal of
file_operations.mmap(). This patchset concentrates upon clearing up
the treatment of stacked filesystems
- "mm: Improve mlock tracking for large folios" from Kiryl Shutsemau
provides some fixes and improvements to mlock's tracking of large
folios. /proc/meminfo's "Mlocked" field became more accurate
- "mm/ksm: Fix incorrect accounting of KSM counters during fork" from
Donet Tom fixes several user-visible KSM stats inaccuracies across
forks and adds selftest code to verify these counters
- "mm_slot: fix the usage of mm_slot_entry" from Wei Yang addresses
some potential but presently benign issues in KSM's mm_slot handling
* tag 'mm-stable-2025-10-01-19-00' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (372 commits)
mm: swap: check for stable address space before operating on the VMA
mm: convert folio_page() back to a macro
mm/khugepaged: use start_addr/addr for improved readability
hugetlbfs: skip VMAs without shareable locks in hugetlb_vmdelete_list
alloc_tag: fix boot failure due to NULL pointer dereference
mm: silence data-race in update_hiwater_rss
mm/memory-failure: don't select MEMORY_ISOLATION
mm/khugepaged: remove definition of struct khugepaged_mm_slot
mm/ksm: get mm_slot by mm_slot_entry() when slot is !NULL
hugetlb: increase number of reserving hugepages via cmdline
selftests/mm: add fork inheritance test for ksm_merging_pages counter
mm/ksm: fix incorrect KSM counter handling in mm_struct during fork
drivers/base/node: fix double free in register_one_node()
mm: remove PMD alignment constraint in execmem_vmalloc()
mm/memory_hotplug: fix typo 'esecially' -> 'especially'
mm/rmap: improve mlock tracking for large folios
mm/filemap: map entire large folio faultaround
mm/fault: try to map the entire file folio in finish_fault()
mm/rmap: mlock large folios in try_to_unmap_one()
mm/rmap: fix a mlock race condition in folio_referenced_one()
...
Pull drm updates from Dave Airlie:
"cross-subsystem:
- i2c-hid: Make elan touch controllers power on after panel is
enabled
- dt bindings for STM32MP25 SoC
- pci vgaarb: use screen_info helpers
- rust pin-init updates
- add MEI driver for late binding firmware update/load
uapi:
- add ioctl for reassigning GEM handles
- provide boot_display attribute on boot-up devices
core:
- document DRM_MODE_PAGE_FLIP_EVENT
- add vendor specific recovery method to drm device wedged uevent
gem:
- Simplify gpuvm locking
ttm:
- add interface to populate buffers
sched:
- Fix race condition in trace code
atomic:
- Reallow no-op async page flips
display:
- dp: Fix command length
video:
- Improve pixel-format handling for struct screen_info
rust:
- drop Opaque<> from ioctl args
- Alloc:
- BorrowedPage type and AsPageIter traits
- Implement Vmalloc::to_page() and VmallocPageIter
- DMA/Scatterlist:
- Add dma::DataDirection and type alias for dma_addr_t
- Abstraction for struct scatterlist and sg_table
- DRM:
- simplify use of generics
- add DriverFile type alias
- drop Object::SIZE
- Rust:
- pin-init tree merge
- Various methods for AsBytes and FromBytes traits
gpuvm:
- Support madvice in Xe driver
gpusvm:
- fix hmm_pfn_to_map_order usage in gpusvm
bridge:
- Improve and fix ref counting on bridge management
- cdns-dsi: Various improvements to mode setting
- Support Solomon SSD2825 plus DT bindings
- Support Waveshare DSI2DPI plus DT bindings
- Support Content Protection property
- display-connector: Improve DP display detection
- Add support for Radxa Ra620 plus DT bindings
- adv7511: Provide SPD and HDMI infoframes
- it6505: Replace crypto_shash with sha()
- synopsys: Add support for DW DPTX Controller plus DT bindings
- adv7511: Write full Audio infoframe
- ite6263: Support vendor-specific infoframes
- simple: Add support for Realtek RTD2171 DP-to-HDMI plus DT bindings
panel:
- panel-edp: Support mt8189 Chromebooks; Support BOE NV140WUM-N64;
Support SHP LQ134Z1; Fixes
- panel-simple: Support Olimex LCD-OLinuXino-5CTS plus DT bindings
- Support Samsung AMS561RA01
- Support Hydis HV101HD1 plus DT bindings
- ilitek-ili9881c: Refactor mode setting; Add support for Bestar
BSD1218-A101KL68 LCD plus DT bindings
- lvds: Add support for Ampire AMP19201200B5TZQW-T03 to DT bindings
- edp: Add support for additonal mt8189 Chromebook panels
- lvds: Add DT bindings for EDT ETML0700Z8DHA
amdgpu:
- add CRIU support for gem objects
- RAS updates
- VCN SRAM load fixes
- EDID read fixes
- eDP ALPM support
- Documentation updates
- Rework PTE flag generation
- DCE6 fixes
- VCN devcoredump cleanup
- MMHUB client id fixes
- VCN 5.0.1 RAS support
- SMU 13.0.x updates
- Expanded PCIe DPC support
- Expanded VCN reset support
- VPE per queue reset support
- give kernel jobs unique id for tracing
- pre-populate exported buffers
- cyan skillfish updates
- make vbios build number available in sysfs
- userq updates
- HDCP updates
- support MMIO remap page as ttm pool
- JPEG parser updates
- DCE6 DC updates
- use devm for i2c buses
- GPUVM locking updates
- Drop non-DC DCE11 code
- improve fallback handling for pixel encoding
amdkfd:
- SVM/page migration fixes
- debugfs fixes
- add CRIO support for gem objects
- SVM updates
radeon:
- use dev_warn_once in CS parsers
xe:
- add madvise interface
- add DRM_IOCTL_XE_VM_QUERY_MEMORY_RANGE_ATTRS to query VMA count
and memory attributes
- drop L# bank mask reporting from media GT3 on Xe3+.
- add SLPC power_profile sysfs interface
- add configs attribs to add post/mid context-switch commands
- handle firmware reported hardware errors notifying userspace with
device wedged uevent
- use same dir structure across sysfs/debugfs
- cleanup and future proof vram region init
- add G-states and PCI link states to debugfs
- Add SRIOV support for CCS surfaces on Xe2+
- Enable SRIOV PF mode by default on supported platforms
- move flush to common code
- extended core workarounds for Xe2/3
- use DRM scheduler for delayed GT TLB invalidations
- configs improvements and allow VF device enablement
- prep work to expose mmio regions to userspace
- VF migration support added
- prepare GPU SVM for THP migration
- start fixing XE_PAGE_SIZE vs PAGE_SIZE
- add PSMI support for hw validation
- resize VF bars to max possible size according to number of VFs
- Ensure GT is in C0 during resume
- pre-populate exported buffers
- replace xe_hmm with gpusvm
- add more SVM GT stats to debugfs
- improve fake pci and WA kunnit handle for new platform testing
- Test GuC to GuC comms to add debugging
- use attribute groups to simplify sysfs registration
- add Late Binding firmware code to interact with MEI
i915:
- apply multiple JSL/EHL/Gen7/Gen6 workarounds properly
- protect against overflow in active_engine()
- Use try_cmpxchg64() in __active_lookup()
- include GuC registers in error state
- get rid of dev->struct_mutex
- iopoll: generalize read_poll_timout
- lots more display refactoring
- Reject HBR3 in any eDP Panel
- Prune modes for YUV420
- Display Wa fix, additions, and updates
- DP: Fix 2.7 Gbps link training on g4x
- DP: Adjust the idle pattern handling
- DP: Shuffle the link training code a bit
- Don't set/read the DSI C clock divider on GLK
- Enable_psr kernel parameter changes
- Type-C enabled/disconnected dp-alt sink
- Wildcat Lake enabling
- DP HDR updates
- DRAM detection
- wait PSR idle on dsb commit
- Remove FBC modulo 4 restriction for ADL-P+
- panic: refactor framebuffer allocation
habanalabs:
- debug/visibility improvements
- vmalloc-backed coherent mmap support
- HLDIO infrastructure
nova-core:
- various register!() macro improvements
- minor vbios/firmware fixes/refactoring
- advance firmware boot stages; process Booter and patch signatures
- process GSP and GSP bootloader
- Add r570.144 firmware bindings and update to it
- Move GSP boot code to own module
- Use new pin-init features to store driver's private data in a
single allocation
- Update ARef import from sync::aref
nova-drm:
- Update ARef import from sync::aref
tyr:
- initial driver skeleton for a rust driver for ARM Mali GPUs
- capable of powering up, query metadata and provide it to userspace.
msm:
- GPU and Core:
- in DT bindings describe clocks per GPU type
- GMU bandwidth voting for x1-85
- a623/a663 speedbins
- cleanup some remaining no-iommu leftovers after VM_BIND conversion
- fix GEM obj 32b size truncation
- add missing VM_BIND param validation
- IFPC for x1-85 and a750
- register xml and gen_header.py sync from mesa
- Display:
- add missing bindings for display on SC8180X
- added DisplayPort MST bindings
- conversion from round_rate() to determine_rate()
amdxdna:
- add IOCTL_AMDXDNA_GET_ARRAY
- support user space allocated buffers
- streamline PM interfaces
- Refactoring wrt. hardware contexts
- improve error reporting
nouveau:
- use GSP firmware by default
- improve error reporting
- Pre-populate exported buffers
ast:
- Clean up detection of DRAM config
exynos:
- add DSIM bridge driver support for Exynos7870
- Document Exynos7870 DSIM compatible in dt-binding
panthor:
- Print task/pid on errors
- Add support for Mali G710, G510, G310, Gx15, Gx20, Gx25
- Improve cache flushing
- Fail VM bind if BO has offset
renesas:
- convert to RUNTIME_PM_OPS
rcar-du:
- Make number of lanes configurable
- Use RUNTIME_PM_OPS
- Add support for DSI commands
rocket:
- Add driver for Rockchip NPU plus DT bindings
- Use kfree() and sizeof() correctly
- Test DMA status
rockchip:
- dsi2: Add support for RK3576 plus DT bindings
- Add support for RK3588 DPTX output
tidss:
- Use crtc_ fields for programming display mode
- Remove other drivers from aperture
pixpaper:
- Add support for Mayqueen Pixpaper plus DT bindings
v3d:
- Support querying nubmer of GPU resets for KHR_robustness
stm:
- Clean up logging
- ltdc: Add support support for STM32MP257F-EV1 plus DT bindings
sitronix:
- st7571-i2c: Add support for inverted displays and 2-bit grayscale
tidss:
- Convert to kernel's FIELD_ macros
vesadrm:
- Support 8-bit palette mode
imagination:
- Improve power management
- Add support for TH1520 GPU
- Support Risc-V architectures
v3d:
- Improve job management and locking
vkms:
- Support variants of ARGB8888, ARGB16161616, RGB565, RGB888 and P01x
- Spport YUV with 16-bit components"
* tag 'drm-next-2025-10-01' of https://gitlab.freedesktop.org/drm/kernel: (1455 commits)
drm/amd: Add name to modes from amdgpu_connector_add_common_modes()
drm/amd: Drop some common modes from amdgpu_connector_add_common_modes()
drm/amdgpu: update MODULE_PARM_DESC for freesync_video
drm/amd: Use dynamic array size declaration for amdgpu_connector_add_common_modes()
drm/amd/display: Share dce100_validate_global with DCE6-8
drm/amd/display: Share dce100_validate_bandwidth with DCE6-8
drm/amdgpu: Fix fence signaling race condition in userqueue
amd/amdkfd: enhance kfd process check in switch partition
amd/amdkfd: resolve a race in amdgpu_amdkfd_device_fini_sw
drm/amd/display: Reject modes with too high pixel clock on DCE6-10
drm/amd: Drop unnecessary check in amdgpu_connector_add_common_modes()
drm/amd/display: Only enable common modes for eDP and LVDS
drm/amdgpu: remove the redeclaration of variable i
drm/amdgpu/userq: assign an error code for invalid userq va
drm/amdgpu: revert "rework reserved VMID handling" v2
drm/amdgpu: remove leftover from enforcing isolation by VMID
drm/amdgpu: Add fallback to pipe reset if KCQ ring reset fails
accel/habanalabs: add Infineon version check
accel/habanalabs/gaudi2: read preboot status after recovering from dirty state
accel/habanalabs: add HL_GET_P_STATE passthrough type
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Improve RPMB frame handling code
- Add support for a new max-sd-hs-hz DT property to limit frequency
- Add support to manage regulator-under-voltage events
- Support regulator-under-voltage for eMMC to mitigate data
corruptions
- Add mmc_read_tuning() to allow a host to validate its tuning
sequence
- Add some helpers to align checks for CMD23 support
- Read the CCCR register for SDIO over SPI rather than the
unsupported CMD7
MMC host:
- Add COMPILE_TEST option for a couple of drivers
- Convert drivers to use the modern PM macros
- dw_mmc-exynos: Enable support for the Exynos8890 variant
- mmc_spi: Don't use crc ack during multiple block read
- renesas_sdhi: Enable 64-bit polling mode for R-Car gen3 and
RZ/G2L SoCs
- rtsx_usb: Add support for over-current-protection
- sdhci-cadence: Add support for multi-block read gap tuning
- sdhci-msm:
- Add support for tuning for SDR50 mode for SD cards
- Enable support for the Lemans variant
- sdhci-pci: Disable SD card clock before update for a few
Intel platforms
- sdhci-pxav3: Add support for UHS pinctrl settings
- tmio: Add 64-bit read/write support in polling mode
MEMSTICK:
- Convert to use timeouts to prevent indefinite waiting
- rtsx_usb: Add support for over-current-protection"
* tag 'mmc-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (77 commits)
dt-bindings: mmc: samsung,exynos-dw-mshc: add specific compatible for exynos8890
mmc: select REGMAP_MMIO with MMC_LOONGSON2
mmc: add COMPILE_TEST to multiple drivers
mmc: core: Improve RPMB frame handling code
mmc: core: Fix variable shadowing in mmc_route_rpmb_frames()
mmc: core: Parse and use the new max-sd-hs-hz DT property
dt-bindings: mmc: controller: Add max-sd-hs-hz property
mmc: sdhci-msm: Enable tuning for SDR50 mode for SD card
dt-bindings: mmc: sdhci-msm: Document the Lemans compatible
mmc: sh_mmcif: Remove dummy PM resume callback
dt-bindings: mmc: sdhci-pxa: Add minItems to pinctrl-names
mmc: sdio: Drop dev_pm_domain_detach() call
mmc: dw_mmc-rockchip: use modern PM macros
mmc: dw_mmc-pci: use modern PM macros
mmc: dw_mmc-k3: use modern PM macros
mmc: dw_mmc: exynos: use modern PM macros
mmc: via-sdmmc: use modern PM macros
mmc: sdhci-msm: use modern PM macros
mmc: mtk-sd: use modern PM macros
mmc: wmt-sdmmc: use modern PM macros
...
