When userspace brings down and deletes a non-transmitted profile,
it is expected to send a new updated Beacon template for the
transmitted profile of that multiple BSSID (MBSSID) group which
does not include the removed profile in MBSSID element. This
update comes via NL80211_CMD_SET_BEACON.
Such updates work well as long as the group continues to have at
least one non-transmitted profile as NL80211_ATTR_MBSSID_ELEMS
is included in the new Beacon template.
But when the last non-trasmitted profile is removed, it still
gets included in Beacon templates sent to driver. This happens
because when no MBSSID elements are sent by the userspace,
ieee80211_assign_beacon() ends up using the element stored from
earlier Beacon template.
Do not copy old MBSSID elements, instead userspace should always
include these when applicable.
Fixes: 2b3171c6fe ("mac80211: MBSSID beacon handling in AP mode")
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215174656.2866319-2-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon frames are required to be sent to the broadcast address, see IEEE
Std 802.11-2020, 11.1.3.1 ("The Address 1 field of the Beacon .. frame
shall be set to the broadcast address"). A unicast Beacon frame might be
used as a targeted attack to get one of the associated STAs to do
something (e.g., using CSA to move it to another channel). As such, it
is better have strict filtering for this on the received side and
discard all Beacon frames that are sent to an unexpected address.
This is even more important for cases where beacon protection is used.
The current implementation in mac80211 is correctly discarding unicast
Beacon frames if the Protected Frame bit in the Frame Control field is
set to 0. However, if that bit is set to 1, the logic used for checking
for configured BIGTK(s) does not actually work. If the driver does not
have logic for dropping unicast Beacon frames with Protected Frame bit
1, these frames would be accepted in mac80211 processing as valid Beacon
frames even though they are not protected. This would allow beacon
protection to be bypassed. While the logic for checking beacon
protection could be extended to cover this corner case, a more generic
check for discard all Beacon frames based on A1=unicast address covers
this without needing additional changes.
Address all these issues by dropping received Beacon frames if they are
sent to a non-broadcast address.
Cc: stable@vger.kernel.org
Fixes: af2d14b01c ("mac80211: Beacon protection using the new BIGTK (STA)")
Signed-off-by: Jouni Malinen <jouni.malinen@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215151134.104501-1-jouni.malinen@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My prior commit here introduced a bug due to copy/paste,
it was iterating the links assigned to 'ctx->replace_ctx'
and I replaced it by iterating links assigned to 'ctx' by
accident, then modified it for the iteration later.
Fix it to iterate the users of the correct chanctx, i.e.
'ctx->replace_ctx'.
Ultimately, this issue led to a crash in a hwsim test
(multi_ap_wps_shared_apdev_csa) because it would actually
do the switch (rather than refuse here) and then later
have a double-free of the original chanctx, because it
was still in use by another interface yet freed as part
of the switching.
Fixes: a1dc648aa7 ("wifi: mac80211: remove chanctx to link back-references")
Link: https://patch.msgid.link/20251121113733.7710a58d45eb.Ie9ec010b52b1baed93dbe44f968c2119b6b5d98d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge CMAC-128 and CMAC-256 handlers since they are almost the same.
This removes duplication.
The comment 'MIC = AES-128-CMAC(IGTK, AAD ...' is out-dated since CMAC
is also used with BIGTK, as is the comment for CMAC-256. Simply remove
the comments.
Tested-on: mac80211_hwsim
Signed-off-by: Chien Wong <m@xv97.com>
Link: https://patch.msgid.link/20251113140511.48658-6-m@xv97.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cross-merge networking fixes after downstream PR (net-6.18-rc6).
No conflicts, adjacent changes in:
drivers/net/phy/micrel.c
96a9178a29 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface")
61b7ade9ba ("net: phy: micrel: Add support for non PTP SKUs for lan8814")
and a trivial one in tools/testing/selftests/drivers/net/Makefile.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For monitoring, userspace will try to configure the VIF sdata, while the
driver may see the monitor_sdata that is created when only monitor
interfaces are up. This causes the odd situation that it may not be
possible to store the MU-MIMO configuration on monitor_sdata.
Fix this by storing that information on the VIF sdata and updating the
monitor_sdata when available and the interface is up. Also, adjust the
code that adds monitor_sdata so that it will configure MU-MIMO based on
the newly added interface or one of the existing ones.
This should give a mostly consistent behaviour when configuring MU-MIMO
on sniffer interfaces. Should the user configure MU-MIMO on multiple
sniffer interfaces, then mac80211 will simply select one of the
configurations. This behaviour should be good enough and avoids breaking
user expectations in the common scenarios.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251110141514.677915f8f6bb.If4e04a57052f9ca763562a67248b06fd80d0c2c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Each link can currently use a chanctx and have another one
reserved, and both of these are also tracked backwards in
the assigned_links and reserved_links lists. If we consider
that there aren't *that* many links, this duplicate book-
keeping isn't necessary.
(I think it used to be necessary before the wiphy locking
changes, when chanctx_mtx existed, because we couldn't do
any interface iterations while holding only chanctx_mtx.)
Additionally, for NAN, we're going to want to track which
chanctxs are in use by the (group of) NAN interfaces. For
those, links don't really make sense as such, so chanctxs
need to be assigned to a different data structure.
Thus, as a first step, remove those back-lists of users
(right now only links) of each channel context. This is a
very basic conversion, ieee80211_vif_use_reserved_switch()
should made to iterate smarter.
Link: https://patch.msgid.link/20251105160431.dbeea1c42e76.I8d273c407274e1c05a4778aa20b56a9f326e87a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current link iteration macros for_each_sdata_link() and
for_each_sdata_link_rcu() are various nested for loops, but
because they iterate all sdata instances and then all links
inside, using 'break' inside the iteration doesn't actually
break out of the whole iteration.
Make it work by tracking whether or not the inner iteration
(over links) actually completed, if it broke out then given
list_for_each_entry() it still iterates all sdata instances
but won't go into them.
Link: https://patch.msgid.link/20251105160431.c21956654fc0.I8d4739af061c44c57d172f19a15303a44ad1e596@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While connecting, the MAC address can already no longer be
changed. The change is already rejected if netif_carrier_ok(),
but of course that's not true yet while connecting. Check for
auth_data or assoc_data, so the MAC address cannot be changed.
Also more comprehensively check that there are no stations on
the interface being changed - if any peer station is added it
will know about our address already, so we cannot change it.
Cc: stable@vger.kernel.org
Fixes: 3c06e91b40 ("wifi: mac80211: Support POWERED_ADDR_CHANGE feature")
Link: https://patch.msgid.link/20251105154119.f9f6c1df81bb.I9bb3760ede650fb96588be0d09a5a7bdec21b217@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cross-merge networking fixes after downstream PR (net-6.18-rc5).
Conflicts:
drivers/net/wireless/ath/ath12k/mac.c
9222582ec5 ("Revert "wifi: ath12k: Fix missing station power save configuration"")
6917e268c4 ("wifi: ath12k: Defer vdev bring-up until CSA finalize to avoid stale beacon")
https://lore.kernel.org/11cece9f7e36c12efd732baa5718239b1bf8c950.camel@sipsolutions.net
Adjacent changes:
drivers/net/ethernet/intel/Kconfig
b1d16f7c00 ("libie: depend on DEBUG_FS when building LIBIE_FWLOG")
93f53db9f9 ("ice: switch to Page Pool")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Management frames on 6 GHz do not include HT Capabilities, causing HT
Action frames to be dropped in ieee80211_rx_h_action(). The current logic
checks only ht_cap.ht_supported, which fails for 6 GHz radios that support
only HE and EHT.
Update the condition to also allow HT Action frame processing when
he_cap.has_he is true. This enables support for HE dynamic SM power save
as defined in IEEE Std 802.11ax-2021, section 26.14.4.
Signed-off-by: Thomas Wu <quic_wthomas@quicinc.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Link: https://patch.msgid.link/20251028043442.523647-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 already reports some basic information in the radiotap header
with the known fields declared by the driver. However, drivers may want
to report more accurate information and in that case the full VHT
radiotap structure needs to be provided.
Add a new RX_FLAG_RADIOTAP_VHT which is set when the VHT information
should be pulled from the skb. Update the code to fill in the VHT fields
to only do so when requested by the driver or if the information has not
yet been set. This way the driver can fully control the information if
it chooses so.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251027142118.0bad1c307a21.I2cf285c20a822698039603f2af00ed9c548f2ee0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, RX bitrate statistics are not updated for packets received
on the mesh forwarding path during fast RX processing. This results in
incomplete RX rate tracking in station dump outputs for mesh scenarios.
Update ieee80211_invoke_fast_rx() to record the RX rate using
sta_stats_encode_rate() and store it in the last_rate field of
ieee80211_sta_rx_stats when RX_QUEUED is returned from
ieee80211_rx_mesh_data(). This ensures that RX bitrate is properly
accounted for in both RSS and non-RSS paths.
Signed-off-by: Sarika Sharma <sarika.sharma@oss.qualcomm.com>
Link: https://patch.msgid.link/20251024043627.1640447-1-sarika.sharma@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multi-radio devices, it is possible to have an MLD AP and a monitor
interface active at the same time. In such cases, monitor mode may not
be able to specify a fixed channel and could end up capturing frames
from all radios, including those outside the intended frequency bands.
This patch adds frequency validation for monitor mode. Received frames
are now only processed if their frequency fall within the allowed ranges
of the radios specified by the interface's radio_mask.
This prevents monitor mode from capturing frames outside the supported radio.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://patch.msgid.link/700b8284e845d96654eb98431f8eeb5a81503862.1758647858.git.ryder.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When ieee80211_stop_ap() deletes the FILS discovery and unsolicited
broadcast probe response templates, the associated interval values
are not reset. This can lead to drivers subsequently operating with
the non-zero values, leading to unexpected behavior.
Trigger repeated retrieval attempts of the FILS discovery template in
ath12k, resulting in excessive log messages such as:
mac vdev 0 failed to retrieve FILS discovery template
mac vdev 4 failed to retrieve FILS discovery template
Fix this by resetting the intervals in ieee80211_stop_ap() to ensure
proper cleanup of FILS discovery and unsolicited broadcast probe
response templates.
Fixes: 295b02c4be ("mac80211: Add FILS discovery support")
Fixes: 632189a018 ("mac80211: Unsolicited broadcast probe response support")
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Link: https://patch.msgid.link/20250924130014.2575533-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_rx_handle_packet(), if the caller does not provide pubsta
information, an attempt is made to find the station using the address 2
(source address) field in the header. Since pubsta is missing, link
information such as link_valid and link_id is also unavailable. Now if such
a situation comes, and if a matching ML station entry is found based on
the source address, currently the packet is dropped due to missing link ID
in the status field which is not correct.
Hence, to fix this issue, if link_valid is not set and the station is an
ML station, make an attempt to find a link station entry using the source
address. If a valid link station is found, derive the link ID and proceed
with packet processing. Otherwise, drop the packet as per the existing
flow.
Fixes: ea9d807b56 ("wifi: mac80211: add link information in ieee80211_rx_status")
Suggested-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250917-fix_data_packet_rx_with_mlo_and_no_pubsta-v1-1-8cf971a958ac@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When moving to the APs channel, ensure we correctly initialise the chandef
and perform the required validation. Additionally, if the AP is beaconing on a
2MHz primary, calculate the 2MHz primary center frequency by extracting
the sibling 1MHz primary and averaging the frequencies to find the 2MHz
primary center frequency.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250918051913.500781-3-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit a8bb74acd8 ("rcu: Consolidate RCU-sched update-side function definitions")
there is no difference between rcu_read_lock(), rcu_read_lock_bh() and
rcu_read_lock_sched() in terms of RCU read section and the relevant grace
period. That means that spin_lock(), which implies rcu_read_lock_sched(),
also implies rcu_read_lock().
There is no need no explicitly start a RCU read section if one has already
been started implicitly by spin_lock().
Simplify the code and remove the inner rcu_read_lock() invocation.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: pengdonglin <pengdonglin@xiaomi.com>
Signed-off-by: pengdonglin <dolinux.peng@gmail.com>
Link: https://patch.msgid.link/20250916044735.2316171-11-dolinux.peng@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
