These are common for all K3 based boards. Add the common values as
defaults and remove from each board defconfig
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
CONFIG_NR_DRAM_BANKS defines the number of DRAM banks on the
device. The default value of NR_DRAM_BANKS for ARCH_K3 is set to 2
(arch/arm/mach-k3/Kconfig:199) but should be 1 for am62x platforms.
This patch updates NR_DRAM_BANKS value for all am62x platforms to 1.
Fixes: 2969ed31b8 ("configs: Add am62x_beagleplay_*_defconfig")
Fixes: 2d257d9279 ("configs: Add configs for AM62x SK")
Fixes: 085cd6459d ("board: phytec: am62x: Add PHYTEC phyCORE-AM62x SoM")
Fixes: 7d1a10659f ("board: toradex: add verdin am62 support")
Signed-off-by: Anshul Dalal <anshuld@ti.com>
SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.
Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Judith Mendez <jm@ti.com> says:
Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.
This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.
This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.
This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.
Any additional tested by's are welcome since I was not able to
test any additional boards.
Tested by running the following commands in u-boot prompt:
=> setenv dorprocboot 1
=> run boot_rprocs
Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com
Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
AM62x BOOTM_LEN is too small to contain OS images. Removing this sets the
size to a default 0x4000000 (for all arm64 devices).
It is unnecessary to specifically call the default size for the other
configs.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Aashvij Shenai <a-shenai@ti.com>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable OF_UPSTREAM for AM625-beagleplay board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
DFU mode on a beagleplay can be used via the Type-C connector by holding
the USR switch while powering on.
Configuration is already provided as fragments for both the A53 and R5
u-boot parts. Include the am62x_a53_usbdfu.config config. The
am62x_r5_usbdfu.config fragment needs to be added should DFU boot be
required as this will disable booting from persistent storage due to
binary size constraints.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reset GPIO handling is done in ETH PHY Class driver.
Enable DM_ETH_PHY.
We don't use Fixed PHY so disable PHY_FIXED.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
There is a default ATF load address that is used for devices that have
ATF running in SRAM. For AM62 and AM62a, ATF runs from DRAM. Instead
of having to override the address in every defconfig, make add a
default for these ATF in DRAM devices.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Stop using the findfdt script and switch to setting the fdtfile from C
code.
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move beagleplay support away from ti/am62x to it's own beagle vendor
folder.
This forms the starting point for new beagle platforms added under it's
own board vendor folder.
As part of this create all the associated files with a bare minimum
beagleplay.c file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
[trini: Update k3-binman.dtsi to use full path to scheme.yaml now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add am62x_beagleplay_* defconfig customized for the configuration of
BeaglePlay and drop the config fragments.
This is in preparation for dropping the dependency on ti vendor folder
entirely.
Signed-off-by: Nishanth Menon <nm@ti.com>
