Enable WGET_HTTPS (no CA verification; also enables dependency MBEDTLS_LIB)
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add Milk-V Mars CM and Mars CM Lite to visionfive2.
These boards were previously supported and then removed in the transition
to OF_UPSTREAM. The dts have landed in the for-next queue so let's add the
boards again.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Add SYS_CPU automatic inclusion jh7110-u-boot.dtsi to item of config list
DEVICE_TREE_INCLUDES as starfive-visionfive2-u-boot.dtsi and rename file.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable CONFIG_DNS for visionfive2 board target. With CONFIG_PROT_DNS_LWIP
enabled and CONFIG_CMD_DNS disabled this restores DNS functionality
displaced by LwIP DNS refactoring during the merge window.
Signed-off-by: E Shattow <e@freeshell.de>
Remove CONFIG_SYS_BOOTM_LEN from all riscv defconfigs where the new
default value is used.
Signed-off-by: Martin Herren <sputnik@on-the-web.ch>
Acked-by: Michal Simek <michal.simek@amd.com> # xilinx_mbv
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
E Shattow <e@freeshell.de> says:
Make consistent use of lowercase hexadecimal prefix '0x' throughout U-Boot.
There are a few remaining uses of uppercase 'X' to denote hexadecimal prefix
or placeholder in documentation and error messages.
External devicetree-rebasing dts/upstream and the generated code of
xilinx/zynq are ignored for the series.
Link: https://lore.kernel.org/r/20250606224558.1117422-1-e@freeshell.de
On several RISC-V boards we have seen that 1 MiB is a insufficient value
for CONFIG_SPL_SYS_MALLOC_SIZE.
For instance qemu-riscv32_spl_defconfig fails booting because u-boot.itb
exceeds 1 MiB.
8 MiB is a reasonable value that allows adding FPGA blobs or splash images
to main U-boot.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The DeepComputing Framework motherboard is a JH7110 device support by the
upstream kernel. Add its device-tree to the list of device-trees to be
included into the starfive_visionfive_defconfig.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: E Shattow <e@freeshell.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present there is a hex value SPL_STACK which both determines whether
SPL has its own initial stack and the hex value of that stack.
Split off the former into SPL_HAVE_INIT_STACK with SPL_STACK depending
on that and only providing the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Resync defconfig files]
Use LwIP network stack and enable wget HTTP command. The tftpput command
is not currently supported by LwIP network stack so remove it.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
("Enable EFI_LOADER_BOUNCE_BUFFER") is not the correct fix for the
problem it describes.
The change of memory addressing leading to side-effects in commit
22f2c9ed9f ("efi: memory: use the lmb API's for allocating and
freeing memory") is remedied by commit 1a48b0be93 ("lmb: prohibit
allocations above ram_top even from same bank").
This reverts commit 9c792ab336.
Enable OF_UPSTREAM to use upstream DT and add starfive/ prefix to
the DEFAULT_DEVICE_TREE. Rename jh7110-starfive-visionfive-2-u-boot.dtsi
to jh7110-starfive-visionfive-2-v1.3b-u-boot.dtsi and set the v1.3b
device tree as the default device tree.
Drop redundant DT files from arch/riscv/dts/ and redundant clock and
reset definitions from include/dt-bindings/.
Since the old clock definitions is a little different from those in
upstream Linux, update the clock definitions in clock drivers
accordingly.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
To restore MMC boot, enable SPL_SYS_MMCSD_RAW_MODE and recover
SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION.
Fixes: 2a00d73d08 ("spl: mmc: Try to clean up raw-mode options")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Our MMC driver for JH7110 boards only supports reading to the low 4 GiB of
memory. Booting boards with more memory requires EFI_LOADER_BOUNCE_BUFFER.
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
To restore MMC boot, enable SPL_SYS_MMCSD_RAW_MODE and recover
SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION.
Fixes: 2a00d73d08 ("spl: mmc: Try to clean up raw-mode options")
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When moving from vendor U-Boot to the upstream U-Boot it is necessary to
reset the environment.
Provide the 'env erase' sub-command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We can use U-Boot for recovering JH7110 based boards via UART
if CONFIG_SPL_YMODEM_SUPPORT=y.
* Send u-boot-spl.normal.out via XMODEM.
* Send u-boot.itb via YMODEM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
Currently in set_fdtfile() we set the value of environment variable fdtfile
unconditionally. The implies that a value in the environment will be
ignored.
With the patch environment variable fdtfile will only be set if it does not
yet exist. This requires that CONFIG_DEFAULT_FDT_FILE is not set.
Now the user can either set and save fdtfile interactively or in the U-Boot
configuration to overrule the device-tree name chosen based on the
hardware in set_fdtfile().
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The VisionFive 2 board supports saving the u-boot environment settings
are saved to on-board SPI flash. However the defconfig enables both
ENV_IS_NOWHERE and ENV_IS_IN_SPI_FLASH, preventing the "saveenv" command
to work. Fix that by disabling ENV_IS_NOWHERE.
Fixes: 7d79bed00c ("configs: starfive: Enable environment in SPI flash support")
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Enable CONFIG_OF_BOARD_SETUP, so we could use ft_board_setup() to fixup
memory size passed to kernel.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
SPL_SYS_MALLOC_CLEAR_ON_INIT would enable SYS_MALLOC_CLEAR_ON_INIT by
default, but that's not need on JH7110, so disable that.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Although PCIE driver already exists, board defconfig isn't configured to
enable PCIE enum on boot, thus USB storage device and NVME drive are not
supported by default. So modify defconfig to enable PCIE auto enum, then
start USB subsystem and scan nvme drive on boot.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
On Starfive Visionfive 2, the u-boot environment settings are saved to
on-board SPI flash. Enable relative configs by default and set offset
and size according to upstream linux dts.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add XHCI_PCI to enable usb3-host functions.
Also add usb command and keyboard config.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Adds a trailing space to SYS_PROMPT to make it easier to distinguish
between commands and the prompt.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable DWC_ETH_QOS and PHY_MOTORCOMM configuration to support ethernet
function for StarFive VisionFive 2 board,including versions 1.2A and
1.3B.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
