boards: arm: nrf52840dongle_nrf52840: Convert to v2

Converts the board to hwmv2

Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>

boards/nordic_nrf/nrf52840dongle/Kconfig

@@ -3,7 +3,7 @@
 # Copyright (c) 2018-2023 Nordic Semiconductor ASA
 # SPDX-License-Identifier: Apache-2.0
 
-if BOARD_NRF52840DONGLE_NRF52840
+if BOARD_NRF52840DONGLE
 
 config BOARD_ENABLE_DCDC
 	bool "DCDC mode"
@@ -26,4 +26,4 @@ config BOARD_SERIAL_BACKEND_CDC_ACM
 	bool "USB CDC"
 	default y
 
-endif # BOARD_NRF52840DONGLE_NRF52840
+endif # BOARD_NRF52840DONGLE

boards/nordic_nrf/nrf52840dongle/Kconfig.defconfig

@@ -4,10 +4,7 @@
 #
 # SPDX-License-Identifier: Apache-2.0
 
-if BOARD_NRF52840DONGLE_NRF52840
-
-config BOARD
-	default "nrf52840dongle_nrf52840"
+if BOARD_NRF52840DONGLE
 
 # To let the nRF5 bootloader load an application, the application
 # must be linked after Nordic MBR, that is factory-programmed on the board.
@@ -83,4 +80,4 @@ endif # BOARD_SERIAL_BACKEND_CDC_ACM
 config BT_CTLR
 	default BT
 
-endif # BOARD_NRF52840DONGLE_NRF52840
+endif # BOARD_NRF52840DONGLE

boards/nordic_nrf/nrf52840dongle/Kconfig.nrf52840dongle

@@ -3,6 +3,7 @@
 # Copyright (c) 2018 Nordic Semiconductor ASA
 # SPDX-License-Identifier: Apache-2.0
 
-config BOARD_NRF52840DONGLE_NRF52840
-	bool "nRF52840 DONGLE NRF52840"
-	depends on SOC_NRF52840_QIAA
+config BOARD_NRF52840DONGLE
+	bool
+	default y
+	select SOC_NRF52840_QIAA

boards/nordic_nrf/nrf52840dongle/board.yml

@@ -0,0 +1,5 @@
+board:
+  name: nrf52840dongle
+  vendor: Nordic Semiconductor
+  socs:
+  - name: nrf52840

boards/nordic_nrf/nrf52840dongle/doc/index.rst

@@ -38,14 +38,14 @@ contains the processor's information and the datasheet.
 Hardware
 ********
 
-The ``nrf52840dongle_nrf52840`` has two external oscillators. The frequency of
+The ``nrf52840dongle/nrf52840`` has two external oscillators. The frequency of
 the slow clock is 32.768 kHz. The frequency of the main clock
 is 32 MHz.
 
 Supported Features
 ==================
 
-The ``nrf52840dongle_nrf52840`` board configuration supports the following
+The ``nrf52840dongle/nrf52840`` board configuration supports the following
 hardware features:
 
 +-----------+------------+----------------------+
@@ -105,7 +105,7 @@ Push buttons
 Programming and Debugging
 *************************
 
-Applications for the ``nrf52840dongle_nrf52840`` board configuration can be
+Applications for the ``nrf52840dongle/nrf52840`` board configuration can be
 built in the usual way (see :ref:`build_an_application` for more details).
 
 Flashing
@@ -144,7 +144,7 @@ device. Make sure ``nrfutil`` is installed before proceeding.
 
    .. zephyr-app-commands::
       :app: zephyr/samples/basic/blinky
-      :board: nrf52840dongle_nrf52840
+      :board: nrf52840dongle/nrf52840
       :goals: build
 
 #. Package the application for the bootloader using ``nrfutil``:
@@ -190,7 +190,7 @@ to the zephyr repository on your computer.
 
    .. zephyr-app-commands::
       :app: mcuboot/boot/zephyr
-      :board: nrf52840dongle_nrf52840
+      :board: nrf52840dongle/nrf52840
       :build-dir: mcuboot
       :goals: build
 
@@ -232,7 +232,7 @@ over Bluetooth).
 
    .. zephyr-app-commands::
       :app: zephyr/samples/subsys/mgmt/mcumgr/smp_svr
-      :board: nrf52840dongle_nrf52840
+      :board: nrf52840dongle/nrf52840
       :build-dir: smp_svr
       :goals: build
 
@@ -269,7 +269,7 @@ name.
 
    .. zephyr-app-commands::
       :app: zephyr/samples/basic/blinky
-      :board: nrf52840dongle_nrf52840
+      :board: nrf52840dongle/nrf52840
       :build-dir: blinky
       :goals: build
       :gen-args: -DCONFIG_BOOTLOADER_MCUBOOT=y
@@ -287,7 +287,7 @@ For Segger J-Link debug probes, follow the instructions in the
 :ref:`nordic_segger` page to install and configure all the necessary
 software. Further information can be found in :ref:`nordic_segger_flashing`.
 
-Locate the DTS file for the board under: boards/arm/nrf52840dongle_nrf52840.
+Locate the DTS file: :zephyr_file:`boards/nordic_nrf/nrf52840dongle/nrf52840dongle_nrf52840.dts`.
 This file requires a small modification to use a different partition table.
 Edit the include directive to include "fstab-debugger" instead of "fstab-stock".
 
@@ -302,7 +302,7 @@ Here is an example for the :zephyr:code-sample:`blinky` application.
 
 .. zephyr-app-commands::
    :zephyr-app: samples/basic/blinky
-   :board: nrf52840dongle_nrf52840
+   :board: nrf52840dongle/nrf52840
    :goals: build flash
 
 Observe the LED on the board blinking.
@@ -310,7 +310,7 @@ Observe the LED on the board blinking.
 Debugging
 =========
 
-The ``nrf52840dongle_nrf52840`` board does not have an on-board J-Link debug IC
+The ``nrf52840dongle/nrf52840`` board does not have an on-board J-Link debug IC
 as some nRF5x development boards, however, instructions from the
 :ref:`nordic_segger` page also apply to this board, with the additional step
 of connecting an external debugger.

boards/nordic_nrf/nrf52840dongle/nrf52840dongle_nrf52840.yaml

@@ -1,4 +1,4 @@
-identifier: nrf52840dongle_nrf52840
+identifier: nrf52840dongle/nrf52840
 name: nRF52840-Dongle-NRF52840
 type: mcu
 arch: arm

boards/nordic_nrf/nrf52840dongle/nrf52840dongle_nrf52840_defconfig

@@ -1,9 +1,5 @@
 # SPDX-License-Identifier: Apache-2.0
 
-CONFIG_SOC_SERIES_NRF52X=y
-CONFIG_SOC_NRF52840_QIAA=y
-CONFIG_BOARD_NRF52840DONGLE_NRF52840=y
-
 # Enable MPU
 CONFIG_ARM_MPU=y