253 lines
4.5 KiB
Plaintext
253 lines
4.5 KiB
Plaintext
/*
|
|
* Copyright (c) 2023 Evan Perry Grove
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/f7/stm32f722Xe.dtsi>
|
|
#include <st/f7/stm32f722z(c-e)tx-pinctrl.dtsi>
|
|
#include "arduino_r3_connector.dtsi"
|
|
#include <zephyr/dt-bindings/input/input-event-codes.h>
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32F722ZE-NUCLEO board";
|
|
compatible = "st,stm32f722ze-nucleo";
|
|
|
|
chosen {
|
|
zephyr,console = &usart3;
|
|
zephyr,shell-uart = &usart3;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
zephyr,dtcm = &dtcm;
|
|
zephyr,canbus = &can1;
|
|
zephyr,code-partition = &slot0_partition;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
green_led: led_1 {
|
|
gpios = <&gpiob 0 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD1";
|
|
};
|
|
blue_led: led_2 {
|
|
gpios = <&gpiob 7 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD2";
|
|
};
|
|
red_led: led_3 {
|
|
gpios = <&gpiob 14 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD3";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button {
|
|
label = "User";
|
|
gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
|
|
zephyr,code = <INPUT_KEY_0>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &green_led;
|
|
led1 = &blue_led;
|
|
led2 = &red_led;
|
|
sw0 = &user_button;
|
|
watchdog0 = &iwdg;
|
|
die-temp0 = &die_temp;
|
|
volt-sensor0 = &vref;
|
|
};
|
|
};
|
|
|
|
&clk_hse {
|
|
clock-frequency = <DT_FREQ_M(8)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&clk_hsi {
|
|
status = "disabled";
|
|
};
|
|
|
|
&pll {
|
|
div-m = <4>;
|
|
mul-n = <216>;
|
|
div-p = <2>;
|
|
div-q = <9>;
|
|
clocks = <&clk_hse>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rcc {
|
|
clocks = <&pll>;
|
|
clock-frequency = <DT_FREQ_M(216)>;
|
|
ahb-prescaler = <1>;
|
|
apb1-prescaler = <4>;
|
|
apb2-prescaler = <2>;
|
|
};
|
|
|
|
&sdmmc1 {
|
|
status = "okay";
|
|
pinctrl-0 = <&sdmmc1_d0_pc8 &sdmmc1_d1_pc9 &sdmmc1_d2_pc10
|
|
&sdmmc1_d3_pc11 &sdmmc1_ck_pc12 &sdmmc1_cmd_pd2>;
|
|
pinctrl-names = "default";
|
|
cd-gpios = <&gpioi 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&adc1 {
|
|
pinctrl-0 = <&adc1_in3_pa3 &adc1_in10_pc0>;
|
|
pinctrl-names = "default";
|
|
st,adc-clock-source = <SYNC>;
|
|
st,adc-prescaler = <2>;
|
|
status = "okay";
|
|
};
|
|
|
|
&dac1 {
|
|
pinctrl-0 = <&dac_out1_pa4>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c2 {
|
|
pinctrl-0 = <&i2c2_scl_pf1 &i2c2_sda_pf0>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&can1 {
|
|
pinctrl-0 = <&can1_rx_pd0 &can1_tx_pd1>;
|
|
pinctrl-names = "default";
|
|
bus-speed = <125000>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart2 {
|
|
pinctrl-0 = <&usart2_tx_pd5 &usart2_rx_pd6 &usart2_rts_pd4 &usart2_cts_pd3>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart3 {
|
|
pinctrl-0 = <&usart3_tx_pd8 &usart3_rx_pd9>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb9>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&spi1 {
|
|
pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pa6 &spi1_mosi_pa7>;
|
|
pinctrl-names = "default";
|
|
cs-gpios = <&gpiod 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&timers1 {
|
|
status = "okay";
|
|
|
|
pwm1: pwm {
|
|
status = "okay";
|
|
pinctrl-0 = <&tim1_ch2_pe11 &tim1_ch3_pe13>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&usart6 {
|
|
pinctrl-0 = <&usart6_tx_pg14 &usart6_rx_pg9>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
zephyr_udc0: &usbotg_fs {
|
|
pinctrl-0 = <&usb_otg_fs_dm_pa11 &usb_otg_fs_dp_pa12 &usb_otg_fs_id_pa10>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>,
|
|
<&rcc STM32_SRC_LSI RTC_SEL(2)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&die_temp {
|
|
status = "okay";
|
|
};
|
|
|
|
&dma2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&iwdg {
|
|
status = "okay";
|
|
};
|
|
|
|
&vref {
|
|
status = "okay";
|
|
};
|
|
|
|
&rng {
|
|
status = "okay";
|
|
};
|
|
|
|
&backup_sram {
|
|
status = "okay";
|
|
};
|
|
|
|
&quadspi {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&quadspi_clk_pb2 &quadspi_bk1_ncs_pb6
|
|
&quadspi_bk1_io0_pd11 &quadspi_bk1_io1_pd12
|
|
&quadspi_bk1_io2_pe2 &quadspi_bk1_io3_pd13>;
|
|
flash-id = <1>;
|
|
status = "okay";
|
|
};
|
|
|
|
&flash0 {
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
/* sectors 0-3 */
|
|
boot_partition: partition@0 {
|
|
label = "mcuboot";
|
|
reg = <0x00000000 DT_SIZE_K(64)>;
|
|
read-only;
|
|
};
|
|
|
|
/* sector 4 */
|
|
storage_partition: partition@10000 {
|
|
label = "storage";
|
|
reg = <0x00010000 DT_SIZE_K(64)>;
|
|
};
|
|
|
|
/* sector 5 */
|
|
slot0_partition: partition@20000 {
|
|
label = "image-0";
|
|
reg = <0x00020000 DT_SIZE_K(128)>;
|
|
};
|
|
|
|
/* sector 6 */
|
|
slot1_partition: partition@40000 {
|
|
label = "image-1";
|
|
reg = <0x00040000 DT_SIZE_K(128)>;
|
|
};
|
|
|
|
/* sector 7 */
|
|
scratch_partition: partition@60000 {
|
|
label = "image-scratch";
|
|
reg = <0x00060000 DT_SIZE_K(128)>;
|
|
};
|
|
};
|
|
};
|