cc18a23ec9
Correct the minimum MTU calculation for GOEP over L2CAP to account for the L2CAP I-frame overhead. - Update BT_BUF_ACL_RX_SIZE default from 264 to 265 bytes for GOEP - Update BT_GOEP_L2CAP_MTU minimum range from 259 to 265 bytes - Add detailed comment explaining L2CAP I-frame field length (6 bytes): * 4 bytes for extended control field * 2 bytes for FCS field The previous calculation only accounted for the L2CAP header (4 bytes) but missed the 6-byte L2CAP I-frame overhead (extended control field and FCS), resulting in an incorrect minimum of 264 bytes instead of the correct 265 bytes. And it causes the minimum MTU of L2CAP to be incorrectly set to 254. The MTU cannot meet the minimum requirement of GOEP MOPL. The correct calculation for GOEP over L2CAP is: 255 bytes (GOEP minimum MTU) + 4 bytes (L2CAP header) + 6 bytes (L2CAP I-frame) = 265 bytes total. Set the default value of CONFIG_BT_BUF_ACL_RX_SIZE to 265 if GOEP is enabled. Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
716 lines
20 KiB
Plaintext
716 lines
20 KiB
Plaintext
# Bluetooth Classic configuration options
|
|
|
|
# Copyright (c) 2016-2020 Nordic Semiconductor ASA
|
|
# Copyright (c) 2015-2016 Intel Corporation
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
menu "Bluetooth Classic Options"
|
|
|
|
config BT_CLASSIC
|
|
bool "Bluetooth BR/EDR support [EXPERIMENTAL]"
|
|
depends on BT_HCI_HOST
|
|
select BT_PERIPHERAL
|
|
select BT_CENTRAL
|
|
select BT_SMP
|
|
select BT_L2CAP_DYNAMIC_CHANNEL
|
|
select CRC
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth BR/EDR support
|
|
|
|
if BT_CLASSIC
|
|
config BT_LIMITED_DISCOVERABLE_DURATION
|
|
int "Maximum duration that a device is in limited discoverable mode in seconds"
|
|
default 60
|
|
range 31 60
|
|
help
|
|
This option sets the maximum duration that a device is in limited discoverable mode in
|
|
seconds.
|
|
|
|
config BT_BR_MIN_ENC_KEY_SIZE
|
|
int
|
|
prompt "Minimum encryption key size accepted in octets" if !BT_SMP_SC_ONLY
|
|
default BT_SMP_MIN_ENC_KEY_SIZE
|
|
range 7 16
|
|
help
|
|
This option sets the minimum encryption key size accepted during pairing
|
|
for classic.
|
|
|
|
config BT_MAX_SCO_CONN
|
|
int "Maximum number of simultaneous SCO connections"
|
|
default 1
|
|
range 1 3
|
|
help
|
|
Maximum number of simultaneous Bluetooth synchronous connections
|
|
supported. The minimum (and default) number is 1.
|
|
|
|
config BT_L2CAP_RX_FLUSH_TO
|
|
hex "Minimum Bluetooth L2CAP RX flush Timeout accepted in milliseconds"
|
|
default 0x0001 if BT_A2DP_SINK
|
|
default 0xFFFF
|
|
range 0x0001 0xFFFF
|
|
help
|
|
This option configures minimum Bluetooth L2CAP RX flush timeout accepted during
|
|
processing peer's l2cap flush timeout configuration.
|
|
The flush timeout applies to all channels on the same ACL logical transport but
|
|
may be overridden on a packet by packet basis by marking individual L2CAP packets
|
|
as non-automatically-flushable via the Packet_Boundary_Flag in the HCI ACL Data packet.
|
|
|
|
config BT_L2CAP_CONNLESS
|
|
bool "Bluetooth L2CAP connectionless data reception [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth L2CAP connectionless data reception
|
|
|
|
config BT_L2CAP_RET
|
|
bool "Bluetooth L2CAP retransmission mode [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth L2CAP retransmission mode
|
|
|
|
config BT_L2CAP_FC
|
|
bool "Bluetooth L2CAP flow control mode [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth L2CAP flow control mode
|
|
|
|
config BT_L2CAP_ENH_RET
|
|
bool "Bluetooth L2CAP enhance retransmission [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth L2CAP enhance retransmission
|
|
|
|
config BT_L2CAP_STREAM
|
|
bool "Bluetooth L2CAP streaming mode [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth L2CAP streaming mode
|
|
|
|
config BT_L2CAP_RET_FC
|
|
def_bool BT_L2CAP_RET || BT_L2CAP_FC || BT_L2CAP_ENH_RET || BT_L2CAP_STREAM
|
|
|
|
if BT_L2CAP_RET_FC
|
|
config BT_L2CAP_FCS
|
|
bool "Bluetooth L2CAP FCS Option [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
depends on BT_L2CAP_STREAM || BT_L2CAP_ENH_RET
|
|
help
|
|
This option enables Bluetooth L2CAP FCS Option
|
|
|
|
config BT_L2CAP_EXT_WIN_SIZE
|
|
bool "Bluetooth L2CAP Extended window size Option [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
depends on BT_L2CAP_STREAM || BT_L2CAP_ENH_RET
|
|
help
|
|
This option enables Bluetooth L2CAP Extended window size Option
|
|
|
|
config BT_L2CAP_MPS
|
|
int "Bluetooth L2CAP MPS for retransmission and Flow control"
|
|
default 48
|
|
range 48 BT_L2CAP_TX_MTU
|
|
help
|
|
Bluetooth L2CAP MPS for retransmission and Flow control
|
|
|
|
config BT_L2CAP_MAX_WINDOW_SIZE
|
|
int "Maximum Windows Size of Retransmission and Flow Control"
|
|
default 1
|
|
range 1 32
|
|
help
|
|
Maximum Windows Size of Retransmission and Flow Control.
|
|
The minimum (and default) number is 1.
|
|
|
|
config BT_L2CAP_BR_RET_TIMEOUT
|
|
int "Retransmission timeout (milliseconds)"
|
|
default 2000
|
|
range 1000 2000
|
|
help
|
|
The Retransmission timeout shall be three times the value of flush timeout,
|
|
subject to a minimum of 1000 milliseconds and maximum of 2000 milliseconds.
|
|
|
|
config BT_L2CAP_BR_MONITOR_TIMEOUT
|
|
int "Monitor timeout (milliseconds)"
|
|
default 12000 if BT_L2CAP_ENH_RET
|
|
default BT_L2CAP_BR_RET_TIMEOUT
|
|
range BT_L2CAP_BR_RET_TIMEOUT 12000
|
|
help
|
|
If a flush timeout exists on the link for Enhanced Retransmission mode and
|
|
both sides of the link are configured to the same flush timeout value then the
|
|
monitor timeout shall be set to a value at least as large as the Retransmission
|
|
timeout otherwise the value of the Monitor timeout shall be six times the value
|
|
of flush timeout, subject to a minimum of the retransmission timeout value and
|
|
a maximum of 12000 milliseconds.
|
|
endif # BT_L2CAP_RET_FC
|
|
|
|
config BT_RFCOMM
|
|
bool "Bluetooth RFCOMM protocol support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth RFCOMM support
|
|
|
|
config BT_RFCOMM_L2CAP_MTU
|
|
int "L2CAP MTU for RFCOMM frames"
|
|
depends on BT_RFCOMM
|
|
default BT_BUF_ACL_RX_SIZE
|
|
range 23 $(INT16_MAX)
|
|
help
|
|
Maximum size of L2CAP PDU for RFCOMM frames.
|
|
RX MTU will be truncated to account for the L2CAP PDU header.
|
|
|
|
config BT_RFCOMM_TX_MAX
|
|
int "Maximum number of pending TX buffers for RFCOMM"
|
|
default BT_BUF_ACL_TX_COUNT
|
|
range BT_BUF_ACL_TX_COUNT $(UINT8_MAX)
|
|
help
|
|
Maximum number of pending TX buffers that have an associated
|
|
sending buf. Normally this can be left to the default value, which
|
|
is equal to the number of session in the stack-internal pool.
|
|
|
|
config BT_HFP_HF
|
|
bool "Bluetooth Handsfree profile HF Role support [EXPERIMENTAL]"
|
|
depends on PRINTK
|
|
select BT_RFCOMM
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth HF support
|
|
|
|
config BT_HFP_AG
|
|
bool "Bluetooth Handsfree profile AG Role support [EXPERIMENTAL]"
|
|
depends on PRINTK
|
|
select BT_RFCOMM
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth AG support
|
|
|
|
if BT_HFP_HF
|
|
config BT_HFP_HF_CLI
|
|
bool "CLI presentation capability for HFP HF [EXPERIMENTAL]"
|
|
default y
|
|
help
|
|
This option enables CLI presentation capability for HFP HF
|
|
|
|
config BT_HFP_HF_VOLUME
|
|
bool "Remote audio volume control for HFP HF [EXPERIMENTAL]"
|
|
default y
|
|
help
|
|
This option enables Remote audio volume control for HFP HF
|
|
|
|
config BT_HFP_HF_CODEC_NEG
|
|
bool "Codec Negotiation for HFP HF [EXPERIMENTAL]"
|
|
help
|
|
This option enables Codec Negotiation for HFP HF
|
|
|
|
config BT_HFP_HF_ECNR
|
|
bool "EC and/or NR function for HFP HF [EXPERIMENTAL]"
|
|
help
|
|
This option enables EC and/or NR function for HFP HF
|
|
|
|
if BT_HFP_HF_CODEC_NEG
|
|
config BT_HFP_HF_CODEC_MSBC
|
|
bool "Support Codec mSBC for HFP HF [EXPERIMENTAL]"
|
|
help
|
|
This option enables Codec mSBC for HFP HF
|
|
|
|
config BT_HFP_HF_CODEC_LC3_SWB
|
|
bool "Support Codec LC3 SWB for HFP HF [EXPERIMENTAL]"
|
|
help
|
|
This option enables Codec LC3 SWB for HFP HF
|
|
endif # BT_HFP_HF_CODEC_NEG
|
|
|
|
config BT_HFP_HF_3WAY_CALL
|
|
bool "Three-way calling for HFP HF [EXPERIMENTAL]"
|
|
help
|
|
This option enables Three-way calling for HFP HF
|
|
|
|
config BT_HFP_HF_ECS
|
|
bool "Enhanced Call Status for HFP HF [EXPERIMENTAL]"
|
|
default y if BT_HFP_HF_3WAY_CALL
|
|
help
|
|
This option enables Enhanced Call Status for HFP HF
|
|
|
|
config BT_HFP_HF_ECC
|
|
bool "Enhanced Call Control for HFP HF [EXPERIMENTAL]"
|
|
default y if BT_HFP_HF_3WAY_CALL
|
|
help
|
|
This option enables Enhanced Call Control for HFP HF
|
|
|
|
config BT_HFP_HF_MAX_CALLS
|
|
int "Maximum supported calls for HFP HF [EXPERIMENTAL]"
|
|
default 2 if BT_HFP_HF_3WAY_CALL
|
|
default 1
|
|
range 1 2
|
|
help
|
|
This option sets maximum supported calls for HFP HF
|
|
|
|
config BT_HFP_HF_VOICE_RECG
|
|
bool "Voice recognition activation for HFP HF [EXPERIMENTAL]"
|
|
help
|
|
This option enables Voice recognition activation for HFP HF
|
|
|
|
config BT_HFP_HF_ENH_VOICE_RECG
|
|
bool "Enhanced Voice Recognition Status for HFP HF [EXPERIMENTAL]"
|
|
select BT_HFP_HF_VOICE_RECG
|
|
help
|
|
This option enables Enhanced Voice Recognition Status for HFP HF
|
|
|
|
config BT_HFP_HF_VOICE_RECG_TEXT
|
|
bool "Voice Recognition Text for HFP HF [EXPERIMENTAL]"
|
|
select BT_HFP_HF_ENH_VOICE_RECG
|
|
help
|
|
This option enables Voice Recognition Text for HFP HF
|
|
|
|
config BT_HFP_HF_HF_INDICATORS
|
|
bool "HF Indicators for HFP HF [EXPERIMENTAL]"
|
|
help
|
|
This option enables HF Indicators for HFP HF
|
|
|
|
config BT_HFP_HF_HF_INDICATOR_ENH_SAFETY
|
|
bool "HF Indicator Enhanced Safety for HFP HF [EXPERIMENTAL]"
|
|
select BT_HFP_HF_HF_INDICATORS
|
|
help
|
|
This option enables HF Indicator Enhanced Safety for HFP HF
|
|
|
|
config BT_HFP_HF_HF_INDICATOR_BATTERY
|
|
bool "HF Indicator Battery level for HFP HF [EXPERIMENTAL]"
|
|
select BT_HFP_HF_HF_INDICATORS
|
|
help
|
|
This option enables HF Indicator Battery level for HFP HF
|
|
|
|
endif # BT_HFP_HF
|
|
|
|
if BT_HFP_AG
|
|
config BT_HFP_AG_EXT_ERR
|
|
bool "Extended Error Result Codes for HFP AG [EXPERIMENTAL]"
|
|
default y
|
|
help
|
|
This option enables Extended Error Result Codes for HFP AG
|
|
|
|
config BT_HFP_AG_CODEC_NEG
|
|
bool "Codec Negotiation for HFP AG [EXPERIMENTAL]"
|
|
help
|
|
This option enables Codec Negotiation for HFP AG
|
|
|
|
if BT_HFP_AG_CODEC_NEG
|
|
config BT_HFP_AG_CODEC_MSBC
|
|
bool "Support Codec mSBC for HFP AG [EXPERIMENTAL]"
|
|
help
|
|
This option enables Codec mSBC for HFP AG
|
|
|
|
config BT_HFP_AG_CODEC_LC3_SWB
|
|
bool "Support Codec LC3 SWB for HFP AG [EXPERIMENTAL]"
|
|
help
|
|
This option enables Codec LC3 SWB for HFP AG
|
|
endif # BT_HFP_AG_CODEC_NEG
|
|
|
|
config BT_HFP_AG_ECNR
|
|
bool "EC and/or NR function for HFP AG [EXPERIMENTAL]"
|
|
help
|
|
This option enables EC and/or NR function for HFP AG
|
|
|
|
config BT_HFP_AG_3WAY_CALL
|
|
bool "Three-way calling for HFP AG [EXPERIMENTAL]"
|
|
help
|
|
This option enables Three-way calling for HFP AG
|
|
|
|
config BT_HFP_AG_MAX_CALLS
|
|
int "Maximum supported calls for HFP AG [EXPERIMENTAL]"
|
|
default 2 if BT_HFP_AG_3WAY_CALL
|
|
default 1
|
|
range 1 2
|
|
help
|
|
This option sets maximum supported calls for HFP AG
|
|
|
|
config BT_HFP_AG_ECS
|
|
bool "Enhanced call status for HFP AG [EXPERIMENTAL]"
|
|
default y if BT_HFP_AG_3WAY_CALL
|
|
help
|
|
This option enables Enhanced call status for HFP AG
|
|
|
|
config BT_HFP_AG_ECC
|
|
bool "Enhanced call control for HFP AG [EXPERIMENTAL]"
|
|
default y if BT_HFP_AG_3WAY_CALL
|
|
help
|
|
This option enables Enhanced call control for HFP AG
|
|
|
|
config BT_HFP_AG_TX_BUF_COUNT
|
|
int "Maximum number of TX buffers for HFP AG [EXPERIMENTAL]"
|
|
default BT_RFCOMM_TX_MAX
|
|
range BT_RFCOMM_TX_MAX $(UINT8_MAX)
|
|
help
|
|
Maximum number of pending TX buffers that have an associated
|
|
sending buf. Normally this can be left to the default value, which
|
|
is equal to the number of session in the stack-internal pool.
|
|
|
|
config BT_HFP_AG_OUTGOING_TIMEOUT
|
|
int "Call outgoing timeout value for HFP AG [EXPERIMENTAL]"
|
|
default 3
|
|
range 1 10
|
|
help
|
|
The option sets the timeout of call outgoing. If the call does
|
|
not switch to alerting state before timeout, it will be
|
|
stopped by the HFP AG. The unit is seconds.
|
|
|
|
config BT_HFP_AG_INCOMING_TIMEOUT
|
|
int "Incoming call timeout value for HFP AG [EXPERIMENTAL]"
|
|
default 3
|
|
range 1 10
|
|
help
|
|
The option sets the timeout of incoming call. If the call does
|
|
not switch to ringing state before timeout, it will be
|
|
stopped by the HFP AG. The unit is seconds.
|
|
|
|
config BT_HFP_AG_ALERTING_TIMEOUT
|
|
int "Call alerting/ringing timeout value for HFP AG [EXPERIMENTAL]"
|
|
default 60
|
|
range 10 60
|
|
help
|
|
The option sets the timeout of call alerting/ringing. If the
|
|
call is not active before timeout, it will be stopped
|
|
by the HFP AG. The unit is seconds.
|
|
|
|
config BT_HFP_AG_PHONE_NUMBER_MAX_LEN
|
|
int "Supported max length of phone number for HFP AG [EXPERIMENTAL]"
|
|
default 32
|
|
range 1 $(UINT8_MAX)
|
|
help
|
|
Supported max length of phone number for HFP AG.
|
|
|
|
config BT_HFP_AG_RING_NOTIFY_INTERVAL
|
|
int "Ring notification interval [EXPERIMENTAL]"
|
|
default 3
|
|
help
|
|
Ring notification interval if the call is in alert state.
|
|
The unit is seconds.
|
|
|
|
config BT_HFP_AG_VOICE_RECG
|
|
bool "Voice recognition activation for HFP AG [EXPERIMENTAL]"
|
|
help
|
|
This option enables Voice recognition activation for HFP AG
|
|
|
|
config BT_HFP_AG_ENH_VOICE_RECG
|
|
bool "Enhanced Voice Recognition Status for HFP AG [EXPERIMENTAL]"
|
|
select BT_HFP_AG_VOICE_RECG
|
|
help
|
|
This option enables Enhanced Voice Recognition Status for HFP AG
|
|
|
|
config BT_HFP_AG_VOICE_RECG_TEXT
|
|
bool "Voice Recognition Text for HFP AG [EXPERIMENTAL]"
|
|
select BT_HFP_AG_ENH_VOICE_RECG
|
|
help
|
|
This option enables Voice Recognition Text for HFP AG
|
|
|
|
config BT_HFP_AG_VOICE_TAG
|
|
bool "Attach a phone number for a voice tag for HFP AG [EXPERIMENTAL]"
|
|
select BT_HFP_AG_VOICE_RECG
|
|
help
|
|
This option enables Attach a phone number for a voice tag for HFP AG
|
|
|
|
config BT_HFP_AG_HF_INDICATORS
|
|
bool "HF Indicators for HFP AG [EXPERIMENTAL]"
|
|
help
|
|
This option enables HF Indicators for HFP AG
|
|
|
|
config BT_HFP_AG_HF_INDICATOR_ENH_SAFETY
|
|
bool "HF Indicator Enhanced Safety for HFP AG [EXPERIMENTAL]"
|
|
select BT_HFP_AG_HF_INDICATORS
|
|
help
|
|
This option enables HF Indicator Enhanced Safety for HFP AG
|
|
|
|
config BT_HFP_AG_HF_INDICATOR_BATTERY
|
|
bool "HF Indicator Battery level for HFP AG [EXPERIMENTAL]"
|
|
select BT_HFP_AG_HF_INDICATORS
|
|
help
|
|
This option enables HF Indicator Battery level for HFP AG
|
|
|
|
config BT_HFP_AG_REJECT_CALL
|
|
bool "Ability to reject a call for HFP AG [EXPERIMENTAL]"
|
|
default y
|
|
help
|
|
This option enables ability to reject a call for HFP AG
|
|
|
|
config BT_HFP_AG_GET_ONGOING_CALL_TIMEOUT
|
|
int "Timeout after the get ongoing calls callback notified (milliseconds) [EXPERIMENTAL]"
|
|
default 10000
|
|
range 1000 10000
|
|
help
|
|
This option sets the timeout after the get ongoing calls callback notified
|
|
|
|
config BT_HFP_AG_INBAND_RINGTONE
|
|
bool "In-band ring tone capability"
|
|
default y
|
|
help
|
|
This option enables In-band ring tone capability
|
|
|
|
endif # BT_HFP_AG
|
|
|
|
config BT_AVDTP
|
|
bool "Bluetooth AVDTP protocol support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth AVDTP support
|
|
|
|
config BT_A2DP
|
|
bool "Bluetooth A2DP Profile [EXPERIMENTAL]"
|
|
select BT_AVDTP
|
|
imply LIBSBC
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables the A2DP profile
|
|
|
|
if BT_AVDTP
|
|
|
|
config BT_AVDTP_RTP_VERSION
|
|
int "Bluetooth AVDTP RTP version"
|
|
default 2
|
|
help
|
|
This option sets the AVDTP RTP protocol version
|
|
|
|
config BT_AVDTP_SIGNAL_SDU_MAX
|
|
int "Maximum size of AVDTP signaling SDU"
|
|
default 512
|
|
range 48 $(UINT16_MAX)
|
|
help
|
|
This option sets the maximum size of AVDTP signaling SDU.
|
|
The default value is 512 bytes.
|
|
|
|
endif # BT_AVDTP
|
|
|
|
if BT_A2DP
|
|
|
|
config BT_A2DP_SOURCE
|
|
bool "Bluetooth A2DP Profile Source Function"
|
|
help
|
|
This option enables the A2DP profile source function
|
|
|
|
config BT_A2DP_SINK
|
|
bool "Bluetooth A2DP Profile Sink Function"
|
|
help
|
|
This option enables the A2DP profile sink function
|
|
|
|
endif # BT_A2DP
|
|
|
|
config BT_AVCTP
|
|
bool "Bluetooth AVCTP protocol support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables Bluetooth AVCTP support
|
|
|
|
config BT_AVRCP
|
|
bool "Bluetooth AVRCP Profile [EXPERIMENTAL]"
|
|
select BT_AVCTP
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables the AVRCP profile
|
|
|
|
if BT_AVRCP
|
|
|
|
config BT_AVRCP_TARGET
|
|
bool "Bluetooth AVRCP Profile Target Function"
|
|
help
|
|
This option enables the AVRCP profile target function
|
|
|
|
config BT_AVRCP_CONTROLLER
|
|
bool "Bluetooth AVRCP Profile Controller Function"
|
|
help
|
|
This option enables the AVRCP profile controller function
|
|
|
|
config BT_AVRCP_VD_RX_SIZE
|
|
int "AVRCP Vendor Dependent RX data buffer Size"
|
|
default 1024
|
|
range 512 $(INT16_MAX)
|
|
help
|
|
Size of the AVRCP Vendor Dependent RX data buffer in bytes.
|
|
This buffer is used for reassembling fragmented AVRCP Vendor Dependent
|
|
commands and responses received from the CT device. If the remote CT
|
|
sends large Vendor-specific PDUs or frequent fragmentation occurs,
|
|
consider increasing this value to avoid incomplete message handling.
|
|
|
|
config BT_AVRCP_BROWSING
|
|
bool "Bluetooth AVRCP Browsing channel support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
select BT_L2CAP_ENH_RET
|
|
help
|
|
This option enables support for the AVRCP Browsing channel
|
|
over Bluetooth BR/EDR.
|
|
|
|
if BT_AVRCP_BROWSING
|
|
|
|
config BT_AVRCP_BROWSING_L2CAP_MTU
|
|
int "L2CAP MTU for AVRCP Browsing Channel"
|
|
default 339
|
|
# For AVRCP Browsing Channel over L2CAP, including:
|
|
# 335 bytes - the minimum MTU for AVRCP Browsing Channel,
|
|
# 4 bytes - L2CAP Header,
|
|
range 339 4096
|
|
help
|
|
Maximum size of L2CAP MTU for AVCTP Browsing Channel.
|
|
RX MTU will be truncated to account for ACL data and type overhead, and
|
|
the L2CAP PDUheader.
|
|
|
|
endif # BT_AVRCP_BROWSING
|
|
|
|
config BT_AVRCP_TG_COVER_ART
|
|
bool "Bluetooth AVRCP Target Cover Art support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
select BT_BIP
|
|
depends on BT_AVRCP_TARGET
|
|
help
|
|
This option enables support for Cover Art in the AVRCP Target
|
|
role over Bluetooth BR/EDR.
|
|
|
|
config BT_AVRCP_CT_COVER_ART
|
|
bool
|
|
select EXPERIMENTAL
|
|
select BT_BIP
|
|
depends on BT_AVRCP_CONTROLLER
|
|
help
|
|
This option enables support for Cover Art in the AVRCP controller
|
|
role over Bluetooth BR/EDR.
|
|
|
|
config BT_AVRCP_CT_COVER_ART_GET_IMAGE_PROPERTIES
|
|
bool "Bluetooth AVRCP Controller Cover Art Get Image Properties support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
select BT_BIP
|
|
select BT_AVRCP_CT_COVER_ART
|
|
depends on BT_AVRCP_CONTROLLER
|
|
help
|
|
This option enables support for Cover Art Get Image Properties in the AVRCP Controller
|
|
role over Bluetooth BR/EDR.
|
|
|
|
config BT_AVRCP_CT_COVER_ART_GET_IMAGE
|
|
bool "Bluetooth AVRCP Controller Cover Art Get Image support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
select BT_BIP
|
|
select BT_AVRCP_CT_COVER_ART
|
|
depends on BT_AVRCP_CONTROLLER
|
|
help
|
|
This option enables support for Cover Art Get Image in the AVRCP Controller
|
|
role over Bluetooth BR/EDR.
|
|
|
|
config BT_AVRCP_CT_COVER_ART_GET_LINKED_THUMBNAIL
|
|
bool "Bluetooth AVRCP Controller Cover Art Get Linked Thumbnail support [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
select BT_BIP
|
|
select BT_AVRCP_CT_COVER_ART
|
|
depends on BT_AVRCP_CONTROLLER
|
|
help
|
|
This option enables support for Cover Art Get Linked Thumbnail in the AVRCP Controller
|
|
role over Bluetooth BR/EDR.
|
|
|
|
endif # BT_AVRCP
|
|
|
|
config BT_DID
|
|
bool "Bluetooth DID Profile [EXPERIMENTAL]"
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables the DID profile
|
|
|
|
if BT_DID
|
|
config BT_DEVICE_VEDNOR_ID
|
|
hex "Bluetooth Device Vendor ID"
|
|
range 0x0000 $(UINT16_MAX)
|
|
default 0x0000
|
|
help
|
|
This option sets the device vendor id
|
|
|
|
config BT_DEVICE_PRODUCT_ID
|
|
hex "Bluetooth Device Product ID"
|
|
range 0x0000 $(UINT16_MAX)
|
|
default 0x0000
|
|
help
|
|
This option sets the device product id
|
|
|
|
config BT_DEVICE_VERSION
|
|
hex "Bluetooth Device Version"
|
|
range 0x0000 $(UINT16_MAX)
|
|
default 0x0000
|
|
help
|
|
This option sets the device version
|
|
|
|
endif # BT_DID
|
|
|
|
config BT_PAGE_TIMEOUT
|
|
hex "Bluetooth Page Timeout"
|
|
default 0x2000
|
|
range 0x0001 0xffff
|
|
help
|
|
This option sets the page timeout value. Value is selected as
|
|
(N * 0.625) ms.
|
|
|
|
config BT_COD
|
|
hex "Bluetooth Class of Device(CoD)"
|
|
default 0
|
|
help
|
|
This option sets the class of device.For the list of possible values please
|
|
consult the following link:
|
|
https://www.bluetooth.com/specifications/assigned-numbers
|
|
|
|
config BT_DEFAULT_ROLE_SWITCH_ENABLE
|
|
bool "Default Bluetooth Role Switch Enable/Disable State"
|
|
help
|
|
This option sets the controller's default link policy to
|
|
enable/disable the role switch.
|
|
|
|
config BT_POWER_MODE_CONTROL
|
|
bool "Bluetooth Power Mode Control(Active/Sniff)"
|
|
help
|
|
This option enables the power mode control feature. This feature
|
|
allows the application to control the power mode of the Bluetooth
|
|
controller.
|
|
|
|
config BT_GOEP
|
|
bool "Bluetooth GOEP Profile [EXPERIMENTAL]"
|
|
select BT_RFCOMM
|
|
select BT_L2CAP_ENH_RET
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables the GOEP profile
|
|
|
|
if BT_GOEP
|
|
config BT_GOEP_RFCOMM_MTU
|
|
int "RFCOMM MTU for GOEP"
|
|
default BT_RFCOMM_L2CAP_MTU
|
|
# For GOEP over RFCOMM, including,
|
|
# 255 bytes - the minimum MTU of GOEP,
|
|
# 4 bytes - L2CAP Header,
|
|
# 5 bytes - 4 bytes for RFCOMM header with extended length, 1 byte for FCS.
|
|
range 264 BT_RFCOMM_L2CAP_MTU
|
|
help
|
|
Maximum size of RFCOMM MTU for GOEP.
|
|
RX MTU will be truncated to account for ACL data and type overhead, the L2CAP PDU header,
|
|
and the RFCOMM header.
|
|
|
|
config BT_GOEP_L2CAP_MTU
|
|
int "L2CAP MTU for GOEP"
|
|
default BT_BUF_ACL_RX_SIZE
|
|
# For GOEP over L2CAP, including,
|
|
# 255 bytes - the minimum MTU of GOEP,
|
|
# 4 bytes - L2CAP Header,
|
|
# 6 bytes - Field length of L2CAP I-frame, including,
|
|
# 4 bytes - extended control field,
|
|
# 2 bytes - FCS field.
|
|
range 265 BT_BUF_ACL_RX_SIZE
|
|
help
|
|
Maximum size of L2CAP MTU for GOEP.
|
|
RX MTU will be truncated to account for ACL data and type overhead, and the L2CAP PDU
|
|
header.
|
|
|
|
config BT_OEBX_RSP_CODE_TO_STR
|
|
bool "Print OBEX response code as strings"
|
|
help
|
|
This configuration enables printing of OBEX response
|
|
codes represented as strings.
|
|
See bt_obex_rsp_code_to_str() for more details.
|
|
|
|
endif # BT_GOEP
|
|
|
|
config BT_BIP
|
|
bool "Bluetooth BIP Profile [EXPERIMENTAL]"
|
|
select BT_GOEP
|
|
select EXPERIMENTAL
|
|
help
|
|
This option enables the BIP profile
|
|
|
|
endif # BT_CLASSIC
|
|
|
|
endmenu
|