Add support for MNT Reform2, it works as a carrier board
with a Firefly iCore-3588Q SoM.
Specification:
- Rockchip RK3588
- LPDDR5X 16/32 GB
- eMMC 128/256 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for Wireless connection
- PCIE M.2 M Key for NVME connection
- DSI to eDP panel
- 1Gb Ethernet w/ Microchip KSZ9310 PHY
Tested using Fedora boot on USB stick and eMMC.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Anbernic RG353M is hardware compatible with RG353P. Only the form-factor
differs. So only one DTS is created for both machines with
"Anbernic RG353P" as default model. If a RG353M is detected, the model
should be overwritten with the correct name.
Actually, it's overwritten with "Anbernic" only making the process of
machine detection a little harder.
However, to determine the size of the string "Anbernic RG353M", it is
sizeof() which is used resulting in obtaining the size of the pointer
(which is 8 bytes on ARM64) not the size of the pointed string.
strlen() should be used instead.
Signed-off-by: David Barbion <davidb@230ruedubac.fr>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK 2 Family is a high-performance SBC (Single Board Computer)
developed by Radxa, based on the Rockchip RK3528A.
The Radxa E20C shares some board characteristics with the ROCK 2 family
boards.
Add support for the ROCK 2A and 2F boards. The radxa-e20c-rk3528 target
is also extended to support booting ROCK 2 boards.
Features tested on a ROCK 2A v1.202:
- SD-card boot
- Ethernet
- USB host (with pending DT changes)
Features tested on a ROCK 2F v1.016:
- SD-card boot
- eMMC boot
- USB host (with pending DT changes)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
I have the ORDOID-GO Super variant of this board. Add myself as a
reviewer to help review future patches targeting this device.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to dynamically select what storage media to use for the U-Boot
environment depending on from what storage media the FIT images was
loaded from, fall back to use env from nowhere.
U-Boot SPL 2025.07 (Jul 13 2025 - 10:07:16 +0000)
Trying to boot from MMC1
...
Loading Environment from MMC... Reading from MMC(0)...
or
U-Boot SPL 2025.07 (Jul 13 2025 - 10:07:16 +0000)
Trying to boot from SPI
...
Loading Environment from SPIFlash...
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include FDTs for all three board variants in the FIT image and adjust
the board selection code to use correct FDT in U-Boot proper.
E.g. use the odroid-go3 DT for a ODROID-GO Super device:
U-Boot 2025.07 (Jul 13 2025 - 10:07:16 +0000)
Model: ODROID-GO Super
DRAM: 1 GiB (total 1022 MiB)
PMIC: RK817 (on=0x80, off=0x08)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A variety of Qualcomm features/fixes for this cycle, notably with a few
new platforms gaining support:
* Initial support for SDM670 (similar to SDM845), SM6350, and SM7150
platforms is added
* USB and UART issues on MSM8916 are addressed (improving stability/
reliability)
* Firmware loading is implemented for the GENI serial engine, this is
used on some platforms to load firmware for i2c/spi/uart to work
Some additional patches like binman support for building MBN files still
need some additional work.
CI: 8ef6ac07b3/pipelines
This board is very tight on space in SPL; in fact with my compiler it
ends up just exactly on the wrong side:
spl/u-boot-spl.bin exceeds file size limit:
limit: 0xa000 bytes
actual: 0xa014 bytes
excess: 0x14 bytes
The repeated "lookup and request" pattern in spl_board_init() suggests
a low-hanging fruit for reducing the code size. This reduces the
object size of spl/board/liebherr/btt/btt.o by 300 bytes.
I've left the lack of error handling as-is; there isn't really
anything to do if it fails, so I suppose the printfs are the best that
can be done.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
The memory size of the 0098 SKU is 8 GB instead of 16 GB.
Fix PID4 0098 Aquila iMX95 definition.
Fixes: 4c93407165 ("toradex: tdx-cfg-block: add new pid4 support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
There is nothing x86-centric in this include file, and moving it will
allow for some drivers to be compile-tested on sandbox.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add identifier for Milk-V Mars CM to dts selection callback in SPL, and
to fdtfile environment variable default value selection in payload.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
NetCube Systems Kumquat is a board based on the Allwinner V3s SoC,
including:
- 64MB DDR2 included in SoC
- 10/100 Mbps Ethernet
- USB-C DRD
- Audio Codec
- Isolated CAN-FD
- ESP32 over SDIO
- 8MB SPI-NOR Flash for bootloader
- I2C EEPROM for MAC addresses
- SDIO Connector for eMMC or SD-Card
- 8x 12/24V IOs, 4x normally open relays
- DS3232 RTC with Battery Backup
- QWIIC connectors for external I2C devices
Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The OrangePi 4A is a typical Raspberry Pi model B sized development
board from Xunlong designed around an Allwinner T527 SoC.
The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header
Add defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The current spl_board_fixups API allows for modification of spl_image
before the SPL jumps to it. This can be used to modify the DT for the
next boot stage, however the current API only allows either the machine
arch or the board to use it.
This limits the utility of the API as there might be certain fixups that
should be applied to all boards sharing the same machine architecture
with others being board specific.
For TI's K3 specifically, this prevents us from performing architecture
level fixups since a lot of TI boards are already making use of the
spl_board_fixups API.
Therefore this patch splits the API into two to allow both board and the
architecture specific fixups. The order is kept as arch then board to
give board specific fixups the precedence.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Fully reset both PCIe controllers before booting the next stage on
Retronix R-Car V4H Sparrow Hawk board. This is necessary especially
in case U-Boot brought up the PCIe controllers, at which point the
next stage might be confused by the state of the PCIe controller.
The reset has to happen this late and not in the PCIe controller
driver, because the SRCR11 bits seem to affect both controllers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable CONFIG_OF_UPSTREAM to receive automatic
device tree updates for the Verdin AM62P.
Remove the now-obsolete device tree files:
- k3-am62p-verdin.dtsi
- k3-am62p-verdin-dev.dtsi
- k3-am62p-verdin-wifi.dtsi
- k3-am62p5-verdin-wifi-dev.dts
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Add initial support for AM62D2-EVM, Kconfig entries for binman, SPL,
base DTS files for u-boot and SPL, HS-SE and HS-FS support and initial
configs with SD-MMC, UART, eMMC and OSPI boot providing a baseline for
further enablement.
Also add labels and targets to AM62A-SK binman to enable AM62D2-EVM
builds to reuse existing binman infrastructure.
Technical Reference Manual - https://www.ti.com/lit/pdf/sprujd4
Schematics Link - https://www.ti.com/lit/zip/sprcal5
Signed-off-by: Paresh Bhagat <p-bhagat@ti.com>
Enable CONFIG_ENV_IS_NOWHERE and force default environment when SoC
boots from serial loader. In this case the U-Boot environment cannot
be stored to flash with the 'saveenv' command.
This makes serial loader boot completely independent from any
environment stored in flash.
Signed-off-by: Eberhard Stoll <eberhard.stoll@kontron.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This is useful for development and manufacturing setups as fastboot
can be used without requiring any user input on the device.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This allows userspace tools like libubootenv to determine the
location of the currently used environment and select a
matching config.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Depending on the MMC boot device, select the proper location for the
environment.
* SD card and eMMC main partition: use offsets from CONFIG_ENV_OFFSET
and CONFIG_ENV_OFFSET_REDUND.
* eMMC boot partition: use offset -2*ENV_SIZE and -ENV_SIZE from the
end of the partition.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The module version this warning is referring to never really existed
except for in-house development and there is a conflict with the
I2C address used for detecting it and the I2C EEPROM of the latest
OSM-S module. Remove the check.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add rauc to bootmeths variable if BOOTMETH_RAUC is enabled. This is
setting a proper default for RAUC enabled systems.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
SoCFPGA updates for v2025.10:
CI: https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27762
This pull request brings a set of updates across SoCFPGA platforms
covering Agilex5, Agilex7, N5X, and Stratix10. The changes include:
* Agilex5 enhancements:
- USB3.1 enablement and DWC3 host driver support
- System Manager register configuration for USB3
- Watchdog timeout increase and SDMMC clock API integration
- dcache handling improvements in SMC mailbox path
- Enable SPL_SYS_DCACHE_OFF in defconfig
* Clock driver improvements:
- Introduce dt-bindings header for Agilex clocks
- Add enable/disable API and EMAC clock selection fixes
- Replace manual shifts with FIELD_GET usage
* DDR updates:
- IOSSM mailbox compatibility check
- Correct DDR calibration status handling
* Device tree changes:
- Agilex5: disable cache allocation for reads
- Stratix10: add NAND IP node
- Enable driver model watchdog
- Enable USB3.1 node for Agilex5
* Config cleanups:
- Simplify Agilex7 VAB defconfig
- Remove obsolete SYS_BOOTM_LEN from N5X VAB config
- Enable CRC32 support for SoCFPGA
- Increase USB hub debounce timeout
Overall this set improves reliability of DDR and cache flows,
adds missing USB and MMC features for Agilex5, and refines clock
and configuration handling across platforms.
This patch set has been tested on Agilex 5 devkit, and Agilex devkit.
Correct the assignment in board_fdt_blob_setup() to use *fdtp instead of
fdtp, ensuring the caller receives the correct FDT address. This
resolves an issue where the device tree pointer was not properly set due
to assigning to the local parameter rather than the dereferenced
pointer.
Fixes: 7c16ebba1e ("board: mpfs_icicle: implement board_fdt_blob_setup()/board_fit_config_name_match()")
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
This reverts commit d37641c61b.
Restore support for environment storage in EXT4 filesystem on eMMC boot.
The previous cleanup incorrectly removed this fallback option which is
needed for boards that store their environment in an EXT4 partition.
This configuration is OS-specific rather than board-dependent and should
remain as it is configurable via menuconfig. Even if it is not described
in ST defconfigs people may have enabled it in their defconfig.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Select SYSRESET on Vexpress64 to enable system reset to support other
features, such as capsule-on-disk. Select SYSRESET_PSCI if PSCI is
inferred from the firmware (via ARM_PSCI_FW).
Select ARM_SMCCC for Vexpress64 boards which in turn selects
ARM_PSCI_FW.
The sysreset uclass unconditionally implements a reset_cpu() function.
Remove the empty reset_cpu() in vexpress64 board code.
Signed-off-by: Debbie Horsfall <debbie.horsfall@arm.com>
Enable the DM_RNG virtio random number generator driver in order to
consume entropy within U-Boot. This allows U-Boot to inject entropy to the
kernel via UEFI, so the kernel can use that early, for instance for
address layout randomisation, or when the kernel does not provide an
entropy driver itself.
Signed-off-by: Debbie Horsfall <debbie.horsfall@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Add board-level code and defconfig for the i.MX943 EVK board, supporting
multiple SOM variants: 19x19 LPDDR5, 19x19 LPDDR4 and 15x15 LPDDR4.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
System Manager provides the last booted and shutdown reasons of the
logical machines (LM) and system using the SCMI misc protocol (Protocol
ID: 0x84, Message ID: 0xA). This path adds get_reset_reason() to query
and print these reasons in SPL and U-Boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
On the RZG2L platform, the advised
TF-A (https://github.com/renesas-rz/rzg_trusted-firmware-a/tree/v2.5/rzg2l)
does not pass any DTB blob to U-Boot.
On the other hand, the RZG2L part of U-Boot expects a DTB to be passed. It
means that if one flashes the latest TF-A as well as the mainline U-Boot,
it will crash trying to dereference the NULL DTB pointer before outputing
anything.
Check if the DTB pointer is NULL before trying to use it.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
