commit 945865a0dd upstream.
Currently, on ASUS projects, the TAS2781 codec attaches the speaker GPIO
to the first tasdevice_priv instance using devm. This causes
tas2781_read_acpi to fail on subsequent probes since the GPIO is already
managed by the first device. This causes a failure on Xbox Ally X,
because it has two amplifiers, and prevents us from quirking both the
Xbox Ally and Xbox Ally X in the realtek codec driver.
It is unnecessary to attach the GPIO to a device as it is static.
Therefore, instead of attaching it and then reading it when loading the
firmware, read its value directly in tas2781_read_acpi and store it in
the private data structure. Then, make reading the value non-fatal so
that ASUS projects that miss a speaker pin can still work, perhaps using
fallback firmware.
Fixes: 4e7035a75d ("ALSA: hda/tas2781: Add speaker id check for ASUS projects")
Cc: stable@vger.kernel.org # 6.17
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Reviewed-by: Baojun Xu <baojun.xu@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20251026191635.2447593-1-lkml@antheas.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b7a0f47aa upstream.
The delayed work uec->work is scheduled in gaokun_ucsi_probe()
but never properly canceled in gaokun_ucsi_remove(). This creates
use-after-free scenarios where the ucsi and gaokun_ucsi structure
are freed after ucsi_destroy() completes execution, while the
gaokun_ucsi_register_worker() might be either currently executing
or still pending in the work queue. The already-freed gaokun_ucsi
or ucsi structure may then be accessed.
Furthermore, the race window is 3 seconds, which is sufficiently
long to make this bug easily reproducible. The following is the
trace captured by KASAN:
==================================================================
BUG: KASAN: slab-use-after-free in __run_timers+0x5ec/0x630
Write of size 8 at addr ffff00000ec28cc8 by task swapper/0/0
...
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x78/0x90
print_report+0x114/0x580
kasan_report+0xa4/0xf0
__asan_report_store8_noabort+0x20/0x2c
__run_timers+0x5ec/0x630
run_timer_softirq+0xe8/0x1cc
handle_softirqs+0x294/0x720
__do_softirq+0x14/0x20
____do_softirq+0x10/0x1c
call_on_irq_stack+0x30/0x48
do_softirq_own_stack+0x1c/0x28
__irq_exit_rcu+0x27c/0x364
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x40/0x60
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
arch_local_irq_enable+0x4/0x8 (P)
do_idle+0x334/0x458
cpu_startup_entry+0x60/0x70
rest_init+0x158/0x174
start_kernel+0x2f8/0x394
__primary_switched+0x8c/0x94
Allocated by task 72 on cpu 0 at 27.510341s:
kasan_save_stack+0x2c/0x54
kasan_save_track+0x24/0x5c
kasan_save_alloc_info+0x40/0x54
__kasan_kmalloc+0xa0/0xb8
__kmalloc_node_track_caller_noprof+0x1c0/0x588
devm_kmalloc+0x7c/0x1c8
gaokun_ucsi_probe+0xa0/0x840 auxiliary_bus_probe+0x94/0xf8
really_probe+0x17c/0x5b8
__driver_probe_device+0x158/0x2c4
driver_probe_device+0x10c/0x264
__device_attach_driver+0x168/0x2d0
bus_for_each_drv+0x100/0x188
__device_attach+0x174/0x368
device_initial_probe+0x14/0x20
bus_probe_device+0x120/0x150
device_add+0xb3c/0x10fc
__auxiliary_device_add+0x88/0x130
...
Freed by task 73 on cpu 1 at 28.910627s:
kasan_save_stack+0x2c/0x54
kasan_save_track+0x24/0x5c
__kasan_save_free_info+0x4c/0x74
__kasan_slab_free+0x60/0x8c
kfree+0xd4/0x410
devres_release_all+0x140/0x1f0
device_unbind_cleanup+0x20/0x190
device_release_driver_internal+0x344/0x460
device_release_driver+0x18/0x24
bus_remove_device+0x198/0x274
device_del+0x310/0xa84
...
The buggy address belongs to the object at ffff00000ec28c00
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 200 bytes inside of
freed 512-byte region
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x4ec28
head: order:2 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0x3fffe0000000040(head|node=0|zone=0|lastcpupid=0x1ffff)
page_type: f5(slab)
raw: 03fffe0000000040 ffff000008801c80 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 03fffe0000000040 ffff000008801c80 dead000000000122 0000000000000000
head: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000
head: 03fffe0000000002 fffffdffc03b0a01 00000000ffffffff 00000000ffffffff
head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000004
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff00000ec28b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff00000ec28c00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff00000ec28c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff00000ec28d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff00000ec28d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Add disable_delayed_work_sync() in gaokun_ucsi_remove() to ensure
that uec->work is properly canceled and prevented from executing
after the ucsi and gaokun_ucsi structure have been deallocated.
Fixes: 00327d7f2c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/cc31e12ef9ffbf86676585b02233165fd33f0d8e.1764065838.git.duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c69ff68b09 upstream.
As part of the registration of a new 'struct usb_phy' with the USB PHY core
via either usb_add_phy(struct usb_phy *x, ...) or usb_add_phy_dev(struct
usb_phy *x) these functions call list_add_tail(&x->head, phy_list) in
order for the new instance x to be stored in phy_list, a static list
kept internally by the core.
After 7d21114dc6 ("usb: phy: Introduce one extcon device into usb phy")
when executing either of the registration functions above it is possible
that usb_add_extcon() fails, leading to either function returning before
the call to list_add_tail(), leaving x->head uninitialized.
Then, when a driver tries to undo the failed registration by calling
usb_remove_phy(struct usb_phy *x) there will be an unconditional call to
list_del(&x->head) acting on an uninitialized variable, and thus a
possible NULL pointer dereference.
Fix this by initializing x->head before usb_add_extcon() has a
chance to fail. Note that this was not needed before 7d21114dc6 since
list_add_phy() was executed unconditionally and it guaranteed that x->head
was initialized.
Fixes: 7d21114dc6 ("usb: phy: Introduce one extcon device into usb phy")
Cc: stable <stable@kernel.org>
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Link: https://patch.msgid.link/20251121-diogo-smaug_typec-v2-1-5c37c1169d57@tecnico.ulisboa.pt
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b120ef99f upstream.
The gaokun_ucsi_probe() uses ucsi_create() to allocate a UCSI instance.
The ucsi_create() validates whether ops->poll_cci is defined, and if not,
it directly returns -EINVAL. However, the gaokun_ucsi_ops structure does
not define the poll_cci, causing ucsi_create() always fail with -EINVAL.
This issue can be observed in the kernel log with the following error:
ucsi_huawei_gaokun.ucsi huawei_gaokun_ec.ucsi.0: probe with driver
ucsi_huawei_gaokun.ucsi failed with error -22
Fix the issue by adding the missing poll_cci callback to gaokun_ucsi_ops.
Fixes: 00327d7f2c ("usb: typec: ucsi: add Huawei Matebook E Go ucsi driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Pengyu Luo <mitltlatltl@gmail.com>
Link: https://patch.msgid.link/4d077d6439d728be68646bb8c8678436a3a0885e.1764065838.git.duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2585973c7f upstream.
The driver previously skipped handling ClearFeature(ENDPOINT_HALT)
when the endpoint was already not halted. This prevented the
controller from resetting the data sequence number and reinitializing
the endpoint state.
According to USB 3.2 specification Rev. 1.1, section 9.4.5,
ClearFeature(ENDPOINT_HALT) must always reset the data sequence and
set the stream state machine to Disabled, regardless of whether the
endpoint was halted.
Remove the early return so that ClearFeature(ENDPOINT_HALT) always
resets the endpoint sequence state as required by the specification.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable <stable@kernel.org>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://patch.msgid.link/20251127033540.2287517-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9415f749d3 ]
handle_pmi_common() may observe an active bit set in cpuc->active_mask
while the corresponding cpuc->events[] entry has already been cleared,
which leads to a NULL pointer dereference.
This can happen when interrupt throttling stops all events in a group
while PEBS processing is still in progress. perf_event_overflow() can
trigger perf_event_throttle_group(), which stops the group and clears
the cpuc->events[] entry, but the active bit may still be set when
handle_pmi_common() iterates over the events.
The following recent fix:
7e772a93eb ("perf/x86: Fix NULL event access and potential PEBS record loss")
moved the cpuc->events[] clearing from x86_pmu_stop() to x86_pmu_del() and
relied on cpuc->active_mask/pebs_enabled checks. However,
handle_pmi_common() can still encounter a NULL cpuc->events[] entry
despite the active bit being set.
Add an explicit NULL check on the event pointer before using it,
to cover this legitimate scenario and avoid the NULL dereference crash.
Fixes: 7e772a93eb ("perf/x86: Fix NULL event access and potential PEBS record loss")
Reported-by: kitta <kitta@linux.alibaba.com>
Co-developed-by: kitta <kitta@linux.alibaba.com>
Signed-off-by: Evan Li <evan.li@linux.alibaba.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://patch.msgid.link/20251212084943.2124787-1-evan.li@linux.alibaba.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220855
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c94291914b ]
On SMP systems the CPU hotplug callbacks in the "starting" range are
invoked while the CPU is brought up and interrupts are still
disabled. Callbacks which are added later are invoked via the
hotplug-thread on the target CPU and interrupts are explicitly disabled.
In the UP case callbacks which are added later are invoked directly without
the thread indirection. This is in principle okay since there is just one
CPU but those callbacks are invoked with interrupt disabled code. That's
incorrect as those callbacks assume interrupt disabled context.
Disable interrupts before invoking the callbacks on UP if the state is
atomic and interrupts are expected to be disabled. The "save" part is
required because this is also invoked early in the boot process while
interrupts are disabled and must not be enabled prematurely.
Fixes: 06ddd17521 ("sched/smp: Always define is_percpu_thread() and scheduler_ipi()")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20251127144723.ev9DuXXR@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c418d8b4d7 ]
For events with inherit_stat enabled, a "read" event will be generated
to collect per task event counts on task exit.
The call chain is as follows:
do_exit
-> perf_event_exit_task
-> perf_event_exit_task_context
-> perf_event_exit_event
-> perf_remove_from_context
-> perf_child_detach
-> sync_child_event
-> perf_event_read_event
However, the child event context detaches the task too early in
perf_event_exit_task_context, which causes sync_child_event to never
generate the read event in this case, since child_event->ctx->task is
always set to TASK_TOMBSTONE. Fix that by moving context lock section
backward to ensure ctx->task is not set to TASK_TOMBSTONE before
generating the read event.
Because perf_event_free_task calls perf_event_exit_task_context with
exit = false to tear down all child events from the context, and the
task never lived, accessing the task PID can lead to a use-after-free.
To fix that, let sync_child_event read task from argument and move the
call to the only place it should be triggered to avoid the effect of
setting ctx->task to TASK_TOMESTONE, and add a task parameter to
perf_event_exit_event to trigger the sync_child_event properly when
needed.
This bug can be reproduced by running "perf record -s" and attaching to
any program that generates perf events in its child tasks. If we check
the result with "perf report -T", the last line of the report will leave
an empty table like "# PID TID", which is expected to contain the
per-task event counts by design.
Fixes: ef54c1a476 ("perf: Rework perf_event_exit_event()")
Signed-off-by: Thaumy Cheng <thaumy.love@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ian Rogers <irogers@google.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: linux-perf-users@vger.kernel.org
Link: https://patch.msgid.link/20251209041600.963586-1-thaumy.love@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab58153ec6 ]
The delayed work item 'imm_tq' is initialized in imm_attach() and
scheduled via imm_queuecommand() for processing SCSI commands. When the
IMM parallel port SCSI host adapter is detached through imm_detach(),
the imm_struct device instance is deallocated.
However, the delayed work might still be pending or executing
when imm_detach() is called, leading to use-after-free bugs
when the work function imm_interrupt() accesses the already
freed imm_struct memory.
The race condition can occur as follows:
CPU 0(detach thread) | CPU 1
| imm_queuecommand()
| imm_queuecommand_lck()
imm_detach() | schedule_delayed_work()
kfree(dev) //FREE | imm_interrupt()
| dev = container_of(...) //USE
dev-> //USE
Add disable_delayed_work_sync() in imm_detach() to guarantee proper
cancellation of the delayed work item before imm_struct is deallocated.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://patch.msgid.link/20251028100149.40721-1-duoming@zju.edu.cn
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96b010536e ]
Up to UEFI spec 2.9, the type byte of CPER struct for ARM processor
was defined simply as:
Type at byte offset 4:
- Cache error
- TLB Error
- Bus Error
- Micro-architectural Error
All other values are reserved
Yet, there was no information about how this would be encoded.
Spec 2.9A errata corrected it by defining:
- Bit 1 - Cache Error
- Bit 2 - TLB Error
- Bit 3 - Bus Error
- Bit 4 - Micro-architectural Error
All other values are reserved
That actually aligns with the values already defined on older
versions at N.2.4.1. Generic Processor Error Section.
Spec 2.10 also preserve the same encoding as 2.9A.
Adjust CPER and GHES handling code for both generic and ARM
processors to properly handle UEFI 2.9A and 2.10 encoding.
Link: https://uefi.org/specs/UEFI/2.10/Apx_N_Common_Platform_Error_Record.html#arm-processor-error-information
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ad2c72e21 ]
Compiling with W=1 with werror enabled produces an error:
drivers/firmware/efi/cper-arm.c: In function ‘cper_print_proc_arm’:
drivers/firmware/efi/cper-arm.c:298:64: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
298 | snprintf(infopfx, sizeof(infopfx), "%s ", newpfx);
| ^
drivers/firmware/efi/cper-arm.c:298:25: note: ‘snprintf’ output between 2 and 65 bytes into a destination of size 64
298 | snprintf(infopfx, sizeof(infopfx), "%s ", newpfx);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
As the logic there adds an space at the end of infopx buffer.
Add an extra space to avoid such warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab08f9c8b3 ]
The log_writes_kthread() calls try_to_freeze() but lacks set_freezable(),
rendering the freeze attempt ineffective since kernel threads are
non-freezable by default. This prevents proper thread suspension during
system suspend/hibernate.
Add set_freezable() to explicitly mark the thread as freezable.
Fixes: 0e9cebe724 ("dm: add log writes target")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6cfd6d7c ]
rs->raid_type is assigned from get_raid_type_by_ll(), which may return
NULL. This NULL value could be dereferenced later in the condition
'if (!(rs_is_raid10(rs) && rt_is_raid0(rs->raid_type)))'.
Add a fail-fast check to return early with an error if raid_type is NULL,
similar to other uses of this function.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 33e53f0685 ("dm raid: introduce extended superblock and new raid types to support takeover/reshaping")
Signed-off-by: Alexey Simakov <bigalex934@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59e25ef2b4 ]
blk_mq_{add,del}_queue_tag_set() functions add and remove queues from
tagset, the functions make sure that tagset and queues are marked as
shared when two or more queues are attached to the same tagset.
Initially a tagset starts as unshared and when the number of added
queues reaches two, blk_mq_add_queue_tag_set() marks it as shared along
with all the queues attached to it. When the number of attached queues
drops to 1 blk_mq_del_queue_tag_set() need to mark both the tagset and
the remaining queues as unshared.
Both functions need to freeze current queues in tagset before setting on
unsetting BLK_MQ_F_TAG_QUEUE_SHARED flag. While doing so, both functions
hold set->tag_list_lock mutex, which makes sense as we do not want
queues to be added or deleted in the process. This used to work fine
until commit 98d81f0df7 ("nvme: use blk_mq_[un]quiesce_tagset")
made the nvme driver quiesce tagset instead of quiscing individual
queues. blk_mq_quiesce_tagset() does the job and quiesce the queues in
set->tag_list while holding set->tag_list_lock also.
This results in deadlock between two threads with these stacktraces:
__schedule+0x47c/0xbb0
? timerqueue_add+0x66/0xb0
schedule+0x1c/0xa0
schedule_preempt_disabled+0xa/0x10
__mutex_lock.constprop.0+0x271/0x600
blk_mq_quiesce_tagset+0x25/0xc0
nvme_dev_disable+0x9c/0x250
nvme_timeout+0x1fc/0x520
blk_mq_handle_expired+0x5c/0x90
bt_iter+0x7e/0x90
blk_mq_queue_tag_busy_iter+0x27e/0x550
? __blk_mq_complete_request_remote+0x10/0x10
? __blk_mq_complete_request_remote+0x10/0x10
? __call_rcu_common.constprop.0+0x1c0/0x210
blk_mq_timeout_work+0x12d/0x170
process_one_work+0x12e/0x2d0
worker_thread+0x288/0x3a0
? rescuer_thread+0x480/0x480
kthread+0xb8/0xe0
? kthread_park+0x80/0x80
ret_from_fork+0x2d/0x50
? kthread_park+0x80/0x80
ret_from_fork_asm+0x11/0x20
__schedule+0x47c/0xbb0
? xas_find+0x161/0x1a0
schedule+0x1c/0xa0
blk_mq_freeze_queue_wait+0x3d/0x70
? destroy_sched_domains_rcu+0x30/0x30
blk_mq_update_tag_set_shared+0x44/0x80
blk_mq_exit_queue+0x141/0x150
del_gendisk+0x25a/0x2d0
nvme_ns_remove+0xc9/0x170
nvme_remove_namespaces+0xc7/0x100
nvme_remove+0x62/0x150
pci_device_remove+0x23/0x60
device_release_driver_internal+0x159/0x200
unbind_store+0x99/0xa0
kernfs_fop_write_iter+0x112/0x1e0
vfs_write+0x2b1/0x3d0
ksys_write+0x4e/0xb0
do_syscall_64+0x5b/0x160
entry_SYSCALL_64_after_hwframe+0x4b/0x53
The top stacktrace is showing nvme_timeout() called to handle nvme
command timeout. timeout handler is trying to disable the controller and
as a first step, it needs to blk_mq_quiesce_tagset() to tell blk-mq not
to call queue callback handlers. The thread is stuck waiting for
set->tag_list_lock as it tries to walk the queues in set->tag_list.
The lock is held by the second thread in the bottom stack which is
waiting for one of queues to be frozen. The queue usage counter will
drop to zero after nvme_timeout() finishes, and this will not happen
because the thread will wait for this mutex forever.
Given that [un]quiescing queue is an operation that does not need to
sleep, update blk_mq_[un]quiesce_tagset() to use RCU instead of taking
set->tag_list_lock, update blk_mq_{add,del}_queue_tag_set() to use RCU
safe list operations. Also, delete INIT_LIST_HEAD(&q->tag_set_list)
in blk_mq_del_queue_tag_set() because we can not re-initialize it while
the list is being traversed under RCU. The deleted queue will not be
added/deleted to/from a tagset and it will be freed in blk_free_queue()
after the end of RCU grace period.
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Fixes: 98d81f0df7 ("nvme: use blk_mq_[un]quiesce_tagset")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edb924a721 ]
In the inline assembly inside load_unaligned_zeropad(), the "addr" is
constrained as input-only operand. The compiler assumes that on exit
from the asm statement these operands contain the same values as they
had before executing the statement, but when kernel page fault happened, the assembly fixup code "bic %2 %2, #0x3" modify the value of "addr", which may lead to an unexpected behavior.
Use a temporary variable "tmp" to handle it, instead of modifying the
input-only operand, just like what arm64's load_unaligned_zeropad()
does.
Fixes: b9a50f7490 ("ARM: 7450/1: dcache: select DCACHE_WORD_ACCESS for little-endian ARMv6+ CPUs")
Co-developed-by: Xie Yuanbin <xieyuanbin1@huawei.com>
Signed-off-by: Xie Yuanbin <xieyuanbin1@huawei.com>
Signed-off-by: Liyuan Pang <pangliyuan1@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2084a7b1 ]
When split svm ranges that have been mapped using huge page should use huge
page size(2MB) to check split range alignment, not prange->granularity that
means migration granularity.
Fixes: 7ef6b2d4b7 ("drm/amdkfd: remap unaligned svm ranges that have split")
Signed-off-by: Xiaogang Chen <xiaogang.chen@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 448ee45353ef9fb1a34f5f26eb3f48923c6f0898)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25faa53646 ]
This commit addresses two issues causing i2c detect to fail.
The identified issues are:
1. Incorrect error handling for BED (Bus Error No ACK/NAK):
Before this commit, Both ALD (Arbitration Loss Detected) and
BED returned -EAGAIN.
2. Missing interrupt status clear after initialization in xfer():
On the K1 SoC, simply fixing the first issue changed the error
from -EAGAIN to -ETIMEOUT. Through tracing, it was determined that
this is likely due to MSD (Master Stop Detected) latency issues.
That means the MSD bit in the ISR may still be set on the next transfer.
As a result, the controller won't work — we can see from the scope that
it doesn't issue any signal.
(This only occurs during rapid consecutive I2C transfers.
That explains why the issue only shows up with i2cdetect.)
With these two fixes, i2c device detection now functions correctly on the K1 SoC.
Fixes: 5ea558473f ("i2c: spacemit: add support for SpacemiT K1 SoC")
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Michael Opdenacker <michael.opdenacker@rootcommit.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20251113-fix-k1-detect-failure-v2-1-b02a9a74f65a@linux.spacemit.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ae4dde6f3 ]
If a DIO read or an unbuffered read request extends beyond the EOF, the
server will return a short read and a status code indicating that EOF was
hit, which gets translated to -ENODATA. Note that the client does not cap
the request at i_size, but asks for the amount requested in case there's a
race on the server with a third party.
Now, on the client side, the request will get split into multiple
subrequests if rsize is smaller than the full request size. A subrequest
that starts before or at the EOF and returns short data up to the EOF will
be correctly handled, with the NETFS_SREQ_HIT_EOF flag being set,
indicating to netfslib that we can't read more.
If a subrequest, however, starts after the EOF and not at it, HIT_EOF will
not be flagged, its error will be set to -ENODATA and it will be abandoned.
This will cause the request as a whole to fail with -ENODATA.
Fix this by setting NETFS_SREQ_HIT_EOF on any subrequest that lies beyond
the EOF marker.
Fixes: 1da29f2c39 ("netfs, cifs: Fix handling of short DIO read")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d85ac939d ]
If a DIO read or an unbuffered read request extends beyond the EOF, the
server will return a short read and a status code indicating that EOF was
hit, which gets translated to -ENODATA. Note that the client does not cap
the request at i_size, but asks for the amount requested in case there's a
race on the server with a third party.
Now, on the client side, the request will get split into multiple
subrequests if rsize is smaller than the full request size. A subrequest
that starts before or at the EOF and returns short data up to the EOF will
be correctly handled, with the NETFS_SREQ_HIT_EOF flag being set,
indicating to netfslib that we can't read more.
If a subrequest, however, starts after the EOF and not at it, HIT_EOF will
not be flagged, its error will be set to -ENODATA and it will be abandoned.
This will cause the request as a whole to fail with -ENODATA.
Fix this by setting NETFS_SREQ_HIT_EOF on any subrequest that lies beyond
the EOF marker.
This can be reproduced by mounting with "cache=none,sign,vers=1.0" and
doing a read of a file that's significantly bigger than the size of the
file (e.g. attempting to read 64KiB from a 16KiB file).
Fixes: a68c74865f ("cifs: Fix SMB1 readv/writev callback in the same way as SMB2/3")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb9f4cca7c ]
Memory allocated by kvcalloc() may come from vmalloc or kmalloc,
so use kvfree() instead of kfree() for proper deallocation.
Fixes: aa36d711e9 ("nvme-auth: convert dhchap_auth_list to an array")
Signed-off-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a32282175 ]
REQ_OP_ZONE_RESET_ALL is a zone management request, and op_is_zone_mgmt()
has returned true for it.
Update the comment to remove the misleading exception note so
the documentation matches the implementation.
Fixes: 12a1c9353c ("block: fix op_is_zone_mgmt() to handle REQ_OP_ZONE_RESET_ALL")
Signed-off-by: shechenglong <shechenglong@xfusion.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c196bf43d7 ]
During system suspend, wakeup capable IRQs for block device can be
delayed, which can cause blk_mq_hctx_notify_offline() to hang
indefinitely while waiting for pending request to complete.
Skip the request waiting loop and abort suspend when wakeup events are
pending to prevent the deadlock.
Fixes: bf0beec060 ("blk-mq: drain I/O when all CPUs in a hctx are offline")
Signed-off-by: Cong Zhang <cong.zhang@oss.qualcomm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
