Replace casting with long to IS_ERR_VALUE() macro to check for error
return values from rate calculation functions. This is the recommended
way to check the return value from clock rate functions.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Replace uclass_get_device_by_ofnode() with syscon_regmap_lookup_by_phandle()
to get the "mediatek,pctl-regmap" syscon device.
Depending on probe order, uclass_get_device_by_ofnode() may fail, but
syscon_regmap_lookup_by_phandle() has logic in it to handle that case
correctly.
The previous implementation could read more than one syscon if the
"mediatek,pctl-regmap" property had more than one phandle, but the one
board with a devicetree that does that is not supported in U-Boot yet,
so we can save that for later (it may never be needed).
Fixes: 424ceba18b ("pinctrl: mediatek: support mediatek,pctl-regmap property")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Pass the unmapped parent ID when setting parent for mux clocks.
For technical reasons, some Mediatek clock driver have a mapping between
the clock IDs used in the devicetree and ID used in the generic clock
framework.
The mtk_clk_mux_set_parent() function is comparing the passed mapped
parent ID against the unmapped IDs in the chip-specific data structures.
Before this change, we were passing the mapped parent ID. When there is
a mapping, this resulted in buggy behavior (usually just incorrectly
failing to find a match and returning an error). We need to pass the
unmapped ID of the parent clock instead for the matching to work
correctly.
Since the reverse lookup is a bit verbose, a helper function is added to
keep the code clean.
Fixes: b135891572 ("clk: mediatek: add of_xlate ops")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Fix typo with correct spelling of "purposes".
Also change "debug" to "debugging" while touching this since that is
the more common phrasing.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Ignore the error return value from mtk_pinconf_bias_set_pupd_r1_r0().
The PUPD/R1/R0 registers only include a small subset of the pins, so
it is normal for this function to return an error for most pins.
Therefore, this error should not be propagated.
This fixes not all pins in a pinmux group being configured in some
cases because the propagated error caused the configuration loop to
exit early.
The rest of the function is refactored to return early on errors to
improve readability.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Set the size of the reg_cals arrays to PINCTRL_PIN_REG_MAX to in all
affected mediatek pinctrl drivers. This is needed to avoid potential
out-of-bounds accesses when they is used in mtk_hw_pin_field_get().
All array members need to be initialized since the code loops from 0
to PINCTRL_PIN_REG_MAX - 1. mt7622_reg_cals was already defined this
way, but the others were not.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Consistently use the device name in debug messages. The clk-uclass file
previously had a mix of printing the dev pointer and the device name.
Changing all to use the device name makes the debug messages more
useful.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Change the format specifier from %p to %s when printing the ofnode name
so that the actual name is printed instead of the pointer address.
Signed-off-by: David Lechner <dlechner@baylibre.com>
With commit 5663b137e6 ("arm: Remove edminiv2 board") the last
ARCH_ORION5X platform was removed. Remove the rest of the architecture
code which is now unused.
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
PHYTEC maintains an actively monitored mailing list for upstream
activities: upstream@lists.phytec.de. Add it to the MAINTAINERS
entries for PHYTEC boards we actively develop and contribute to.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
BOOTP does not support dynamic lease expiration. Using random MAC
addresses on R5 network boot binaries would result in continuously
allocated IPs without proper release.
Since only one interface is enabled for network boot, rely on the
MAC address provided by the efuses instead.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
BOOTP does not support dynamic lease expiration. Using random MAC
addresses on R5 network boot binaries would result in continuously
allocated IPs without proper release.
Since only one interface is enabled for network boot, rely on the
MAC address provided by the efuses instead.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tom Rini <trini@konsulko.com> says:
This series builds on top of what Beleswar Padhi did in [1]. While
there's still discussion about the mkimage related parts, the linker
portion appears to the reliable path forward. An alternative that I had
mentioned before, and was part of previous discussions on this topic[2]
is in the end I believe not reliable enough. While we can take an output
file and pad it to where we think it needs to be, ultimately the linker
needs to place the symbol where we want it and if that isn't where we
pad to, we have a different problem. So what this series does (but each
commit message elaborates on the arch-specific linker scripts being
inconsistent) is make sure the linker script will place the required
symbol at 8-byte alignment, and then also use an ASSERT to fail the
build if this would not be true due to some unforseen event.
[1]: https://lore.kernel.org/u-boot/20260112101102.1417970-1-b-padhi@ti.com/
[2]: https://source.denx.de/u-boot/u-boot/-/issues/30
Link: https://lore.kernel.org/r/20260115222828.3931345-1-trini@konsulko.com
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Rewrite the '.rel.dyn' (u-boot.lds) to follow modern practices, and
include the 8-byte alignment at the end of the section.
- Expands the '.dynamic' section (u-boot-64.lds) to be more readable
when adding a second statement to the section.
- Aligns the final section before _end (for U-Boot) or _image_binary_end
or __bss_end (for xPL phases) by 8-bytes by adding '. = ALIGN(8);' to
the final section before the symbol or changing an existing ALIGN(4)
statement.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Aligns the final section before _image_binary_end (for xPL phases) by
8-bytes by adding '. = ALIGN(8);' to the final section before the
symbol.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Aligns the final section before _end (for U-Boot) or _image_binary_end
(for xPL phases) by 8-bytes by adding '. = ALIGN(8);' to the final
section before the symbol.
- Remove a now-spurious '. = ALIGN(x);' statement that was intended to
provide the above alignments.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Aligns the final section before _end by 8-bytes by adding '. =
ALIGN(8);' or changing an existing ALIGN(4) statement.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Aligns the final section before _end 8-bytes by adding '. = ALIGN(8);'
to the final section before the symbol.
- Remove a now-spurious '. = ALIGN(x);' statement that was intended to
provide the above alignments.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Aligns the final section before _end (for U-Boot) or _image_binary_end
(for xPL phases) by 8-bytes by adding '. = ALIGN(8);' to the final
section before the symbol. For SPL we need this in two places to cover
all build configurations.
- Remove now-spurious '. = ALIGN(x);' statements that were intended to
provide the above alignments.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Aligns the final section before _end (for U-Boot) or _image_binary_end
(for xPL phases) by 8-bytes by adjusting the ALIGN(4) statement to be
ALIGN(8) in the final section before the symbol.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Tested-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Remove part of what Marek Vasut did in commit 9ed99e2eea ("m68k:
Assure end of U-Boot is at 8-byte aligned offset") as we now better
understand what can trigger failure and check for it.
- Rewrite the '.dynsym' section to follow modern practices, and include
the 8-byte alignment at the end of the section.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Expands some linker sections to be more readable when adding a second
statement to the section.
- Aligns the final section before _end (for U-Boot) or
_image_binary_end or __bss_end (for xPL phases) by 8-bytes by adding
'. = ALIGN(8);' to the final section before the symbol.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
- Remove now-spurious '. = ALIGN(x);' statements that were intended to
provide the above alignments.
Tested-by: Michal Simek <michal.simek@amd.com> # Zynq
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
[trini: Also update arch/arm/cpu/armv8/u-boot.lds as Ilas requested]
Signed-off-by: Tom Rini <trini@konsulko.com>
If we have ASSERT macros that validate the position of
_image_binary_end, our awk expression will report a string that causes
the rest of our check to fail with garbage values. Have it exit after
the first match to fix this.
Signed-off-by: Tom Rini <trini@konsulko.com>
The OMAP2 SPL linker script (also used for K3 platforms) currently uses
a 4-byte alignment directive after the __u_boot_list section. This
alignment directive only advances the location counter without padding
the actual binary output.
When objcopy extracts u-boot-spl-nodtb.bin, it includes only actual
data, stopping at the last byte of __u_boot_list (e.g., 0x41c359fc),
not an aligned address (e.g., 0x41c35a00). So, when the FIT image
containing device trees is concatenated to the SPL binary, it gets
appended at this unaligned file size, causing libfdt validation failure.
To fix this, move the alignment directive into the __u_boot_list section
itself and make it 8-byte aligned as per DT spec. This forces the linker
to include padding as part of the section data, ensuring objcopy
includes the padding bytes in the binary and the appended FIT image
starts at an 8-byte aligned boundary.
Reported-by: Anshul Dalal <anshuld@ti.com>
Closes: https://lore.kernel.org/u-boot/DFJ950O0QM0D.380U0N16ZO19E@ti.com
Fixes: 0535e46d55 ("scripts/dtc: Update to upstream version v1.7.2-35-g52f07dcca47c")
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Pull request efi-2026-04-rc1-2
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/29050
Documentation:
* Update StarFive JH7110 common description
* Add TI AM62D documentation
* Update urllib3 version for building
* Update links to doc/develop/falcon.rst
* Describe QEMU networking
* kdoc: handle the obsolescensce of docutils.ErrorString()
* Fix typo "addtional" -> "additional" in pflash section.
UEFI:
* Fix boot failure from FIT with compressed EFI binary
Others:
* cmd/meminfo: Correct displaying addresses above 4 GiB
* test:
- Consider configuration in meminfo test
- Consider initf_malloc is only traced with EARLY_TRACE
- Clean up test_trace.py code
Updates to the JH7110 common description:
- add detailed overview of JH-7110 SoC and boot process
- revise descriptions of deprecated StarFive loader modes
- refresh build directions grouped with SPL debug advice
- reduce usage instructions into common methods shared by supported boards
- cite starfive_visionfive2 board maintainer description of StarFive loader
- cite published datasheets for ambient operating temperature data
Redundant/deprecated sections of each board doc are dropped accordingly:
- deepcomputing fml13v01
- milk-v mars
- pine64 star64 (also add inclusion of JH7110 common description)
- visionfive2
Signed-off-by: E Shattow <e@freeshell.de>
The GitHub dependabot tool has reported a "medium" priority bug
CVE-2026-22701, with this package. Update to the patched version.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
PRIuN, PRIxN, etc macros are defined in <inttypes.h>, without it being
included errors like:
tools/amlimage.c:124:38: error: expected ‘)’ before ‘PRIu8’
tools/amlimage.c:126:31: error: expected ‘)’ before ‘PRIu32’
Can be hit depending on the host compiler and HOSTCFLAGS.
Fixes: 18c1654567 ("tools: mkimage: Add Amlogic Boot Image type")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Ferass El Hafidi <funderscore@postmarketos.org>
On my AN7581 board, the same change in the Airoha ATF-2.10 source code
causes instability in eMMC reading. After the patch, in about 9 of 10
cases, ATF BL2 is unable to read FIP image from the eMMC flash. Thus
BL31 and U-Boot are unable to start.
Lets revert commit 7cb79f8d3d ("arm: dts: an7581: set r_smpl for MMC
in U-Boot") until the issue will be investigated.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
The GitHub dependabot tool has reported one "high" priority bug,
CVE-2026-21441, with this package. Update to the patched version.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
The bootm command can handle the compressed image, but current
code fails to boot from it.
## Loading kernel (any) from FIT Image at a8000000 ...
<snip>
Compression: gzip compressed
Data Start: 0xa80000d4
Data Size: 10114520 Bytes = 9.6 MiB
Architecture: AArch64
OS: EFI Firmware
Load Address: 0x90000000
<snip>
Uncompressing Kernel Image to 90000000
## Transferring control to EFI (at address a80000d4) ...
Booting <NULL>
Not a PE-COFF file
Loading image failed
To take care of the compressed image, the load address needs
to be passed instead of the original compressed image address.
Signed-off-by: Masahisa Kojima <kojima.masahisa@socionext.com>
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
The ErrorString() and SafeString() docutils functions were helpers meant to
ease the handling of encodings during the Python 3 transition. There is no
real need for them after Python 3.6, and docutils 0.22 removes them,
breaking the docs build
Handle this by just injecting our own one-liner version of ErrorString(),
and removing the sole SafeString() call entirely.
Reported-by: Zhixu Liu <zhixu.liu@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Upstream: https://git.kernel.org/linus/00d95fcc4dee66dfb6980de6f2973b32f973a1eb
[j.ne: Adapted from Linux to U-Boot]
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a chapter about networking to the QEMU board documentation.
Describe both different types of networking as well as different emulated
NICs.
Suggested-by: Manjae Cho <manjae.cho@samsung.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The output of the meminfo command depends on several Kconfig variables.
These need to be taken into account to provide valid test results.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <simon.glass@canonical.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/29031
- Fix interrupt storms in Linux on the imx93_frdm board.
- Defconfig update for tqma6 board.
- Miscellaneous cleanups/improvements for imx93_evk.
- Allow booting from both USB controlles on i.MX6 DHSOM.
- Handle third MAC address for SMARC i.MX95
Input from TQ-Systems hardware qualification team.
Fixes performance issues if ethernet and display are used simultaneously.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Add a common, MMC and SPI defconfigs with the general configurations
and use them in the variant-specific defconfigs.
while at it:
- set BOOTCOMMAND to mmcboot as it is used on majority of other TQ modules
as the default
- remove DEFAULT_FDT_FILE - The kernel device tree is set at runtime.
- remove CONFIG_CMD_EXT4_WRITE - EXT4 with default features cannot be
written from U-Boot.
- add CONFIG_FDT_FIXUP_PARTITIONS - This is needed to propagate MTD
partition setup via devicetree to linux.
Signed-off-by: Paul Gerber <Paul.Gerber@ew.tq-group.com>
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
